Question about 1995 Toyota 4Runner

1 Answer

A repair shop is replacing the clutch on my 1995 toyota 4runner. 5-spd.. They are also telling me that the input shaft needs to be replaced. Is this necessary?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 101 Answers

The shaft has what are called splines and if the shaft gets twisted the clutch is unable to move on the shaft and would require replacement

Posted on Mar 19, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 67 falcon with 170 six and 3 speed stick trans. Is there a 5 speed that will easily install into this car?


there are 5 speed transmissions that will fit in so look first at the 5 speed ford transmissions because the bell housing mounting bolts may be the same pattern
Ford has done a lot to the heads of the engine bit the basic block remained the same
other 5 boxes such as toyota have been used as replacements but you need an adaptor plate and a different clutch plate to accommodate the different spline size of the input clutch shaft
There will be a requirement to change drive shaft lengths and sliding spline and rear engine mounting brackets
talk around with transmission repair shops and get ideas and speed / performance shops will also be able to help with information
the replacement is not easy but with good prior information you will be able to do the job

Nov 08, 2017 | Cars & Trucks

1 Answer

1993 4runner SR5. How do I replace the clutch?


Well it depends if it is a manual you have to take back drive shaft off and drop transsmission but if it is automatic you may just be able to drop your belhousing and take off bolts holding clutch and swap it out

Jun 06, 2015 | 1993 Toyota 4Runner

1 Answer

How clutch replacement


disconnect battery, remove starte motor, remove drive shafts, support and remove cross member,remove clutch slave cylinder, remove bellhousing bolts and while suspending transmission remove and lower transmission.//remove preasure plate and clutch. Good idea to replace spigot bearing and throw out bearing while you do job. allow 4-5 hrs for r&r. Refit in reverse order.

Nov 17, 2012 | 1987 Toyota 4Runner

1 Answer

Rive shaft have a heavy noise, sound like a fan, my que4stion is:, is it drive shaft or U joints?


is it a clunking when you drive? probably the U-Joint, I have had to replace mine that was worn, and my drive shaft was going clunk everytime I would ease off the clutch and onto the throttle

Nov 14, 2011 | 1995 Toyota 4Runner

1 Answer

1984 transmission wines in all gears 5 spd trans am 305 engine. How can i get the wine to go away?


If this vehicle is an automatic ....the whinning your hearing is the bearing on the oil pump in the torque converter. Time for a new transmission.
If its a stick the noise may be the throw out bearing of the clutch. Time for a new clutch.
If it is a stick and your replacing the clutch have the pilot bearing and input shaft (of transmission) bearing replaced, and if the fly wheel doesn't have any meat on it replace it.

Apr 01, 2010 | 1984 Pontiac Firebird

1 Answer

1991 toyota 4runner new trany leals oil from between the engine and trany only when hot. does this trany have a vent line, where is it. is there problems with the input shaft seal??? please help


I beleive its going to be your input shaft seal. Even if a new one was installed, some times on installation can get messed up. If you had the tranny job done in a shop and still under warranty, take it back, they should fix it no charge.

good luck

Mar 02, 2010 | 1991 Toyota 4Runner

1 Answer

Toyota 4runner catalytic converter replacement


YOU REMOVE THE 4 BOLTS BEFORE AND AFTER THE CAT.
ENSURE THE OLD INLET AND OUTLET GASKETS ARE REMOVED AND REPLACED BE FORE INSTALLING THE NEW CAT WITH NEW BOLTS.
ABOUT $800 FOR THE PART AND A HOURS LABOUR.
AN MUFFLER SHOP SHOULD BE ABLE TO INSTALL A UNIVERSAL
CAT FOR LESS.

Aug 13, 2009 | 1995 Toyota 4Runner

1 Answer

Need Directions to Replace clutch in a1993 5spd.toyota 4runnerV6


start off bt taking off your shifter, then disconnect the wires,cables, and the 4x4 linkage, the drop out both drive shafts, support the tranny and transfer case then remove the tranny mount. take out the bolts on the bell housing that go into the motor the pull out the slave cylinder,and the last thing to remove is the cross member that holds up your tranny. after that slide the tranny back about 6 inches tor until it's free from the block and lower it down. after you get it on the ground pull of out clutch fork that is in the bell housing of your tranny, pull the bearing off the shaft that is in the bell housing as well. and last but not least take off the clutch plate ans the clutch disk that is on the fly wheel on your block. and i cant stress this enough be careful when you pull the tranny out and make sure it will not fall on you. so please do it carefully. And take your time.

Mar 26, 2009 | 1993 Toyota 4Runner

2 Answers

My 1989 5 spd cherokee clutch "popped" while driving home. Is there a spring that broke? What do you think?


What do you mean by "popped" After the popping, what does the pedal feel like now? As far as I know, the clutch control "linkage" on your vehicle is hydraulic. Inspect system for leaks, replace failed parts & bleed. If problem is with the clutch itself, transmission needs to be removed and all components inspected and replaced as needed.

Dec 23, 2008 | 1989 Jeep Cherokee

Not finding what you are looking for?
1995 Toyota 4Runner Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...