Question about 1993 Toyota Camry V6

Open Question

Toyota Camry 2,2l,Stv,1993 mod, Bytte av termostat

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 98 Answers

SOURCE: How to remove ignition cylinder from Toyota Camry 1993

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

Posted on Nov 23, 2008

  • 101 Answers

SOURCE: 1993 Toyota Camry V6 Timing Settings

Get a T belt from toyota. It has 3 white lines on it and and arrow mark. 2 lines are solid and one is broken. Put the arrow facing away from the engine. The cam gears have a dot punched into them near a certain tooth. This is where the solid white lines will line up with. The crank gear will have a dot also. It will line up at 90 degrees from the top, towards the front of the car. This is where the broken line will match up with. With the belt installed with all lines on their proper dots and arrow away from the engine, you valve timming is correct.
Of course you need to remove and compress the tensioner also. I assume you know this already since you didn't ask.

Posted on Apr 16, 2009

ronaldo_ross
  • 1056 Answers

SOURCE: 1993 Toyota Camry - code for radio lost, security lock out-need.

Try the reset button on the radio.

Posted on Jun 30, 2009

projdoc
  • 2236 Answers

SOURCE: replace alternator belt only for 1993 toyota camry

loosen the mounting bolts on the alternator, remove the old belt, replace with the new belt, slightly tighten the top mounting bolt, pull the alternator up until the belt is tight or if there is an adjustment bolt, crank down until tight (shouldn't bow more than 1"), and tigten other hardware.

Posted on Aug 12, 2009

  • 1986 Answers

SOURCE: How to change a third brake light bulb for 1993 Toyota Camry?

open the trunk and look up along the top of the bumper and you should see two screws / nuts that secure the light assembly.

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 toyota camry


See here for all the checks you can do on the ignition system. You will need a good multimeter

http://www.turboninjas.com/camry/ig.pdf

Mar 27, 2015 | 1993 Toyota Camry

1 Answer

I need instructions to install a termostat for my 1994 Toyota Camry 4C


Follow the top radiator hose and it will lead you to the thermostat housing.Only two bolts holding it.Remove and replace thermostat.fill with coolant.Run engine with cap off till fluid starts circulating and then put cap back on and monitor if the tempt remains constant at operating tempt.

Jun 23, 2011 | 1994 Toyota Camry

1 Answer

Toyota camry 1993 battery not charging


Yes, you are right alternator is dead.

Aug 30, 2009 | 1993 Toyota Camry V6

2 Answers

1993 Toyota Camry


93 Camry fuel filter is right below the brake master cylinder

Aug 08, 2009 | 1993 Toyota Camry V6

1 Answer

Installing power window on 1993 toyota camry


Take the door panel off. Disconnect the window and tape it up. Remove the regulator out off the door cavity.

Jun 06, 2009 | 1993 Toyota Camry V6

1 Answer

How to change a third brake light bulb for 1993 Toyota Camry?


open the trunk and look up along the top of the bumper and you should see two screws / nuts that secure the light assembly.

Mar 26, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
1993 Toyota Camry V6 Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...