Question about 2007 Chevrolet Silverado 1500 2WD

1 Answer

I have a matchead size chip in the hard plastic on my center console is there a colored filler i can use to patch it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

Use a dab of grey silicone and match with factory touch up paint.

Posted on Mar 19, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to locate the transmission speed sensor in my car..


It should be at the tail of the trans...pending engine size...Some are at the center...
Look for a plastic sensor it should be an off white color..Also probably hard to see and get to ....
It would be a good idea to have vehicle on a lift.You may have to remove a skid plate.....It should have 2 wires going to it....Althoough I have seen some that you can see from the top of the engine
located near the tail................Hope this helps............Metalpoet Level 2 certified tech.

Mar 28, 2011 | 2002 Ford Escort

1 Answer

How to change shifter light on floor center console, ive removed the main bolts from the rear of console and the brass fittings inside the center compartment but can not get it to move, ive also tried the...


The shift indicator light is under the plastic trim panel on the center console.

Open the lid to the console, and the latch location, you will see the separation. Use a plastic trim tool in here, or along the sides.
The silver color where the cup holders are at is all 1 part, and comes out together. The shift indication scale stays with the shifter ( the chrome trim stays with the shifter as well ).
The spring clips can be tough to pop the 1st time. Best to use a plastic trim tool or if you do not have that, a plastic putty knife.

Nov 20, 2010 | 2004 Ford F150

1 Answer

Patch on passager side dast


go to petboys and get a dash cover

Mar 29, 2010 | 2006 Nissan Pathfinder

1 Answer

How do I remove the center console in my 1999 Oldsmobile Cutlass?


very carefuly,pry on the plastic molding, it will pop loose,but it is very hard to pop loose

Mar 17, 2010 | 1999 Oldsmobile Cutlass

2 Answers

Where is the manual gearbox oil filler plug on 2006 Hyundai Accent MC


hi from uk if memory serves ?the g/box oil level/filler plug is-- as you open the hood/bonnet in uk then look down at the gearbox on the front side behind radiator the filler plug is half way down in the center of g/box the filler is a hexagonal heade nut and the size of wrench needed is 17 or 19 mm ?? the level is correct if when you remove plug the oil is at the lower end of hole hope this helps ?

Mar 04, 2010 | 2006 Hyundai Accent

1 Answer

Trying to locate manual release tab 1998 Corvett fuel door


The fuel filler door release is the black button at the front of the center console storage compartment.

If your fuel filler door release won’t operate, there is a manual release tab. The tab is located against the upper trim in the rear compartment on the driver's side.

Nov 19, 2009 | 1998 Chevrolet Corvette

2 Answers

Where is the transmission fluid filler on ford fiesta 1996 auto


You need a medium-sized funnel; or a specially-designed transmission fluid filler funnel with a short hose attached to it (at Auto parts store for $5)... use a medium-sized funnel....

The filler tube is the same as the transmission dipstick tube.
Check the fluid level with the engine running, in park.
before adding fluid, turn off engine.

Insert the funnel into the tansmission dipstick tube, slowly pour in fluid (slowly!)..

In an emergency, you can make a funnel with paper or cardboard or sheet of plastic. ... and maybe duct tape...

Hope this helps!




Sep 10, 2009 | Ford F Cars & Trucks

1 Answer

1990 cutlass ceira how do you replace drivers door side mirror


Outside Mirrors REMOVAL & INSTALLATION Standard
  1. Remove the door trim panel and detach the inner panel water deflector. With the glass in the down position, pull out the front portion of the glass run weatherstrip. Fig. 1: Unfasten the attaching nuts from the mirror base studs, then remove the mirror 8c45877.gif


  1. Remove the attaching bolts and screws from the front glass run channel lower retainer to filler, then rotate retainer rearward.
  2. Remove the noise control patch to gain access to the screw at the belt, then remove the screw.
  3. Remove the filler attaching screws at the top front of the window frame, then remove the mirror and filler from the door.
  4. Remove the attaching nuts from the mirror base studs, then remove the mirror. To install:
  5. Be sure that the mirror gasket is aligned.
  6. Replace the mirror and filler on the door. Install the filler attaching screws at the top front of the window frame. Attach the nuts to the mirror studs and tighten.
  7. Install the screw at the belt, then insert the noise control patch.
  8. Insert the retainer, then install the attaching bolts and screws to the front glass run channel lower retainer to filler.
  9. Replace the front portion of the glass run weatherstrip, insert the inner panel water deflector, then reinstall the door trim panel.
Manual Remote
  1. Remove the mirror remote control escutcheons and door trim panel. Detach the inner panel water deflector. NOTE: Right side remote mirror may require detaching part of the instrument panel.
  2. With the glass in the down position, pull out the front portion of the glass run weatherstrip.
  3. Remove the attaching bolts and screws from the front glass run channel lower retainer to filler and rotate retainer rearward.
  4. Remove the noise control patch to gain access to the 0.3 in. (7mm) screw at the belt and remove the screw.
  5. Remove the filler attaching screws at the top front of the window frame.
  6. Remove the mirror base with mirror and cable assembly from the door.
  7. Remove the mirror to filler attaching nuts and remove the mirror and cable from filler. To install:
  8. Be sure cable is routed around front glass run channel retainer and installed to clip.
  9. Install and connect the cable to the filler.
  10. Attach the filler nuts to the mirror, then tighten to 72 inch lbs. (8 Nm).
  11. Install the mirror base with the mirror and cable assembly to the door.
  12. Insert the filler attaching screws to the top of the window frame, then install the screw to the belt.
  13. Secure the noise control patch.
  14. Attach the bolts and screws to the front of the glass run channel lower retainer and filler.
  15. Install the glass run weatherstrip.
  16. Attach the inner panel water deflector, door trim panel and mirror remote control escutcheon.
Electric Remote
  1. Disconnect the negative battery cable.
  2. Remove the mirror remote control escutcheons and door trim panel. Detach the inner panel water deflector and the electrical connector for the mirror. NOTE: Right side remote mirror may require detaching part of the instrument panel.
  3. With the glass in the down position, pull out the front portion of the glass run weatherstrip.
  4. Remove the attaching bolts and screws from the front glass run channel lower retainer to filler and rotate retainer rearward.
  5. Remove the noise control patch to gain access to the 0.3 in. (7mm) screw at the belt and remove the screw.
  6. Remove the filler attaching screws at the top front of the window frame.
  7. Remove the mirror base with mirror and electric connector from the door.
  8. Remove the mirror to filler attaching nuts and remove the mirror and electric wire from filler.
  9. To install, reverse Steps 1 through 6. Be sure electric wire is routed around front glass run channel retainer and installed to the clip. Tighten the nuts to 72 inch lbs. (8 Nm).
  10. Connect the negative battery cable, then reset the clock, radio and any other accessories if required.

Aug 25, 2009 | 1990 Oldsmobile Cutlass Ciera

1 Answer

2008 cobalt coupe interior


Looks can be decieving ... more than likely it is due to the shift linkage and the underside of the center console. remember it is all molded plastic so they can have the top look identical and the bottom (or underside) could be completely different.

Jun 20, 2009 | Chevrolet Cobalt Cars & Trucks

2 Answers

2004 KIa optima center consol


Should be screws hidden under plugs that are the same color as the plastic. Try to remove cup holder etc there should be little pop outs. I will check on one of the kias in the lot. send me a response so I can put you at the top of the list.

Jul 15, 2008 | 2004 Kia Optima

Not finding what you are looking for?
Cars & Trucks Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...