Question about 2004 Lincoln LS

1 Answer

MY MECANIC ASK ME TO BAY A AC COMPRESSOR MANIFOLD PIPE, SOMETHING THAT GO NEXTO CO THE COMPRESSOR, WHERE I CAN FIND THAT ON LINE THANKYOU VERY MUCH JOHN

Posted by on

1 Answer

I have a 2004 Lincoln LS

There is no way you need a compressor
hose or manifold assy,unless it cracked
from vibration

Why do you have to get it, when your
paying them anyway ?

Do they have A/C experience

I will tell you from close to 50 years
experience, that ONLY a Dealer part will
fit, when it comes to A/C or Power Steering.

So you will have to go to the dealers parts
counter,order it,pay for it,and they will call
when it comes in.

You will be paying big time, list price, unless
your a business with a state tax form on file

Posted on Mar 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

AC compressor clicks on and off while running?


the compressor will cycle on/off when the cabin temperature is reached
the larger pipe will be cold to touch as it is the suction line for the compressor
if you have a problem with the ac ,it will not work the compressor at all and the lines will not get cold
When in doubt take it to an accredited ac specialist shop and have the system check out.

Aug 11, 2015 | 2000 Cadillac Escalade

1 Answer

2007 ac low pressure port


It'll be in the engine bay.
Start by looking at the compressor and following the pipe.
It is a small car so you should find it pretty quickly.

Jun 19, 2014 | 2007 Suzuki Reno Hatchback

1 Answer

Where is the low pressure AC port on a 2000 mercury sable


it will be in the larger pipe near the compressor or in the line at an accessible point.. The low pressure is the suction line from inside the car to the compressor.

May 10, 2014 | 2000 Mercury Sable

1 Answer

Charge ac


The high pressure service port is located on the liquid line between the condenser and the evaporator, near the front of the engine compartment. The low pressure service port is located on the compressor manifold, directly over the suction port of the compressor. Make sure you know what your doing if you connect the wrong thing to the wrong port you can blow something up.

Mar 22, 2012 | 1998 Dodge Durango

1 Answer

The air coditioner quit..makes loud noise. how do I remove the compressor ?


you will need to recover 1st the freon in the vehicle , once that is done, you need to remove the drive belt to free up the AC pulley. once that is done, you will then need to remove the AC line manifold from the back of the AC Compressor. The AC manifold needs to be covered by a ZIP LOCK bag to not allow any moistutre in it. Remove bolts that hold down the AC Compressor and the electrical harness attacked to it.

Aug 27, 2010 | 1993 Oldsmobile Cutlass Supreme

1 Answer

1991 freelander stalling


on the inlet manifold is a breather from the engine i think on this year so check for a split vacumn hose or a split breather pipe ,failing which it could be the thingy on the back end of the butterfly ,their is a sensor but iam pretty sure its a breather pipe or something stupid ,also pull the vac pipe out of the servo and just try pùtting a plug into pipe in case the servo diaphram has split

May 27, 2010 | 2002 Land Rover Freelander

1 Answer

Hot do you take off a 98 GMC 5.7 vortec intake


Note, removing the upper intake manifold is not necessary when removing lower intake manifold, they are removed as an assembly.
Disconnect negative battery cable. Drain cooling system. Remove air cleaner assembly and inlet duct. Mark and remove distributor. Remove upper radiator hose at thermostat housing. Disconnect accelerator and cruise control cables. Remove heater hoses from intake manifold. Remove EGR pipe.
Disconnect fuel lines at rear of engine. Remove AC compressor and set aside(leave hoses connected). Remove canister purge solenoid. Disconnect theSCPI injector, ignition coil, Ignition Control Module, generator,IAC motor, TP sensor, O2 sensor, Exhaust Gas Recirculation valve and Engine Coolant Temperature sensor wiring harness connectors. Remove PCV valve and hose. Remove lower intake manifold bolts. Remove lower intake manifold.
Installation.
Always use New O-rings when reconnecting fuel lines at rear of engine. Apply a bead of RTV silicone sealer along the front and rear sealing surfaces of the block.See Fig.6. Install new gaskets and intake manifold on block while RTV is still wet to the touch. Use Threadlock 12345382 or equivalent to lower intake manifold bolts. Tighten lower intake manifold bolts in sequence to specification table. See fig. 7. To complete installation, reverse removal procedure.f52665d.gifabc2b5f.gif

Oct 10, 2009 | 1998 GMC Sierra

1 Answer

1998 Jetta TDI - AC compressor turns but no cooling


something not right here ,firstly why didnt you just renew the clutch instead of a complete compressor ?? secondly do you have a machine to recharge the system and if so are you using it correctly ,the reason i ask is because in the machine the low and high pressure pipes are interconnected in the body of the machine so yes it would show these pressures.When refilling a car once machine has weighed the gas leaving the bottle shut off the red line and start engine leaving the blue line connected ,run engine at 2000rpm with A/C on full for about 3 mins to draw the gas in from the machine .Then close blue line and and do a recovery to see how much gas was left in the machine.Also did you put compressor oil in when you re fitted the compressor about 100cc is enough ,this is better put in directly into compressor ,then vacumn to about -750mg or a stage one vac pump and omit the oil recovery cycle .When running the air temperature coming out should be about 7.5centigrade is good but some cars will drop to 5C anything below 9C is ok ,and forget to clean out pollen filter

Jun 08, 2009 | 1997 Volkswagen Jetta

1 Answer

Air conditioning not cool


The charging port is in the larger of the 2 AC lines from the AC compressor on the engine, it will be near to or in the round cannister (called an Accumulator) that larger AC line goes near the firewall at the back of the engine bay.

Apr 28, 2009 | 1998 Chevrolet Malibu

Not finding what you are looking for?
2004 Lincoln LS Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...