Question about 2005 Chevrolet Silverado

1 Answer

Ther is a knock in the steering colom when you turn left or right.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 447 Answers

You may have a noisy Upper Intermediate Steering shaft. There is a service bulletin regarding this type of noise [bulletin #00-02-003N, dated March 26, 2008] that explains what needs to be done. It's just a service bulletin and NOT a recall. Most competent shops will have seen this problem many times and will know what to replace. Good luck, hope this helps!

Posted on Mar 18, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rpm increases when I turn the steering wheel to the left or right. Neutral or in gear

i think it is normal because the steering wheel is run by the engine thru belt, so when you turn either to left or to the right the rpm will increase or there is a noise engine, unless it is a knocking sound, which is not normal

Sep 24, 2011 | 2005 Ford Five Hundred

1 Answer

Ignition is locked and will not turn

check your steering colom it may be stuck use force move it left then right at the same time while turninig the key

Sep 09, 2011 | 2001 Chrysler Town & Country

1 Answer

Click or popping noise when turning left or right when taking off. also horn stuck it blows by itself, i think it could be haunted. lol need help please

nose in front is needs axles checked and replaced ....horn is probally a problem in steering colom....wire grounding out working the tilt wheel up and down might help tell....hope it helps

Nov 16, 2010 | 2005 Pontiac Grand Am

1 Answer

Chevy cobalt noise knocking in front end when you turn the steering wheel from left to right. Also knocking noise over bumps.

Hello and welcome. this noise is normally caused by a noisey steering I-shaft. there is a steering shaft that goes in between the steering column and the steering gear. this shaft has a slip joint that becomes noisey. all you need to do is lube the i-shaft with some special lube and you will be good to go

Sep 30, 2010 | 2006 Chevrolet Cobalt

1 Answer

How to adjust the stering wheel on 2008 ford 150 4x4 fx4

looking at the steering wheel frome the drivers seat it should be on the lower left hand side of the steering colome pull back on the small handel and it should tilt

Jun 05, 2010 | 2008 Ford F-150

1 Answer

I have a pontiac sunfire 2001 and the blinkers have stopped working, is this and easy fix?

sounds like your turn signal switch on your sreering colom common problem haft to take the steering colom appart to fix

Mar 13, 2010 | 2001 Pontiac Sunfire

1 Answer

Steering colom will not let key turn

Try this if steering wheel is turned slightly to one side meaning front wheels turn steering wheel to that sam side take strain off the lock in steering column and key should turn. I believe that the steering wheel is locked. If it doesn't work turn left or right and try again. Good Luck and contact if you need more help.

Jan 05, 2009 | 2005 Nissan Titan

2 Answers

2004 GMC Yukon Steering Problem

I have the same problem, low speeds and only when i turn to the left, steering locks or jams, but only at low speeds, and parking lot manuevers. Will replace gear box, simple 3 or 4 bolts, and can easily be done in a drive way or home garage. Hope this helps! 90% its the gear box even if you have the right one already.
Tips** you should have the 680 gear box and not the old one (670 3 bolt patter). The 680 should have 4 bolts. But there are issues and may need to be replaced. I had a faulty one!

Dec 16, 2008 | 2004 GMC Yukon

Not finding what you are looking for?
2005 Chevrolet Silverado Logo

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides