Question about Mercury Villager

1 Answer

I clipped the wires that go to the alterator on my 2001 murcury villager estate now i need some kida diagram to help me put them back together

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 662 Answers

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Remove /replace engine in a 1998 Murcury Villager mini Van

Why? If you are serious, you need a repair manual. try this
try youtube, you may find a detailed video of someone doing it.

Feb 27, 2015 | 1998 Mercury Villager

2 Answers

My air conditioner quit working and now my 2001 mercury villager estate is getting hot

Can you tell if the radiator fan is working ? It should come on when the engine temp reaches 225 degrees and when the ac is switched on.

May 20, 2014 | Cars & Trucks

1 Answer

How do i change the airfilter on a 95 murcury villager

The air filter is not quickly changed. I found it best to disconnect and remove the battery first. Then the housing to the air filter is more easily accessed. The air filter housing is that big ugly black plastic box sitting on an angle behind the battery. Loosen the two hose clamps on the downstream side, un-clip the wired sensor on the housing, and remove the 3 bolts that hold the box to the car body (one high, 2 low) Pop off the air-in port and pull the air-filter box from the car. See how it\'s wire clamped on 3 sides and use pliers to lift them off their stays. Open and remove old filter, wipe or blow out any debris and gunk found in the housing, put in new filter. Carefully re-clamp shut, being sure it\'s seated correctly. Lightly clean and grease the ports that will be re-clamped and put it all back. Yeah, it\'s tedious, but now you know how it all fits together. And you can clean all that acid on your battery, battery posts and tray before putting that back in while you\'re at it, making for a better connection there too.

Feb 28, 2014 | 1995 Mercury Villager

1 Answer

Transfer case wiring

If you go to autozones website and make a free account, you can logon to that account and put in the year, make and model of your car and look for the free repair diagrams. They have the wiring diagrams. Then change the make and model year to the donor car and look for those diagrams.

Feb 19, 2014 | 2001 Dodge Durango

2 Answers

O2 sensor replacement can't locate it on the downstream 2001 murcury villager

The downstream sensor will be AFTER the cat. It may be on the top of the exhaust pipe and hard to see. As a rule it is close to the convertor.

Oct 11, 2011 | 2001 Mercury Villager

1 Answer

Looking for the sensor that the reads the outside air temperature and displays it on the dash of a 2001 quest.If anyone knows the name and location of it. I have a 2001 Mercury Villager estate and the...

bpagett: the component you are referring to is called an "AMBIENT SENSOR". It is located behind the front bumper cover on the radiator core support near the center of the vehicle. The part is about 2 inches long and bullet shaped. It has the wire harness plugged into it. Sorry I don't have a part number for you.

May 29, 2009 | 2001 Mercury Villager

1 Answer

Rear door speakers

this website will give you wiring diagrams for your cd player and suburban.

Feb 09, 2009 | 1994 Chevrolet Suburban

5 Answers

Mercury Villager headlight assembly diagaram for removal

This is easy. Lift the lid open. Look at the back of the sealed beam and you will see a clip and an o ring. Pull the clip up and pull wires back toward the driver's seat. Unscrew the o ring and firmly pull the bulb out toward the driver again. Note the 3 tabs on the bulb seat and realign the new bulb with those tab ( 2 bottom, 1 top). Replace with #9007 them both.

Jul 01, 2008 | 1995 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts


Level 3 Expert

80531 Answers


Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides