Question about 1986 Toyota Pickup 4WD

1 Answer

1986 22r 4x4 pick-up I need tips to replace clutch master cylinder and clutch release cylinder.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

Start with the slave (release) cylinder. First take off the line and plug it with a golf tee or a short piece of hose with a bolt in the end. Remove the slave cylinder. Fill the new one with fluid and do the reverse. Then do the same thing with the master cylinder being careful not to lose any fluid. You may need to add fluid and bleed the system when finished.

Posted on Mar 18, 2011

Testimonial: "Thank You. I'll give it a try "

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Clutch stays down. Slowly will take of with clutch fully pressed. Does not slip.dont understand


It sounds as though the clutch pressure plate has become weak.

When you press the clutch pedal the release/throwout bearing presses against the centre of the clutch pressure plate. This causes the metal 'fingers' -the springs- on the pressure plate to flex and release pressure on the driven plate - momentarily disconnecting the drive from engine to gearbox.

The link below is of generic clutch images
how clutch works Google Search

A weak pressure plate isn't fully releasing the driven plate. If you're going to do any replacing of parts - a clutch should be replaced in 3 units: Pressure plate, driven plate and release/throwout bearing.

May 05, 2016 | Cars & Trucks

1 Answer

How much is it to replace a clutch release bearing on a 1990 Nissan pathfinder 4x4 v6 se manual transmission


Rate is about 6 hours to remove and replace the transmission. At$100 an hour, that is $600 there, plus parts. If you doing this, Have the clutch, pressure plate and flywheel replaced also. Along with the master cylinder.

Mar 17, 2016 | Nissan Cars & Trucks

2 Answers

I am replacing the clutch on my 1987 Ford ranger 4x4 and can't figure out how to remove the slave cylinder supply line.


You have to push the white part around the outside in to release it. Use a small screwdriver if you don't have the tool. It will take a while to get it to release. Sometimes they can be hard to remove.

Mar 02, 2011 | Ford Ranger Cars & Trucks

1 Answer

I replaced clutch master cylinder and clutch release cylinder,bleeding system still don't have clutch pressure. Clutch pedal doesn't have pressure.


If you can press the clutch fork ( the part that the release cylinder pushes) in by hand then your clutch has failed and needs to be changed. If not then I suspect there is still air in the system. Most master cylinder replacements require a "bench bleed" before installation. this involves putting it in a vise, filling with fluid and attaching a hose that runs the fluid back into the resevoir. Then you press the plunger and release slowly until all the air is expelled. This can take quite a few times.

Jan 02, 2011 | Honda Accord Cars & Trucks

1 Answer

Clucth master cylinder isuzu mu 1994 4jg2 3.1 DT


can assist with master cylinder and slave cylinder layout isuzu bighorn bj2

Mar 05, 2010 | Isuzu MU-7 Cars & Trucks

1 Answer

Chevy l989 4X4 5 speed manual clutch not working


Almost every time a clutch is replaced in a GM with hydraulic release system that system is replaced as well. You can try, and try, and try again to bleed it, but you will eventually replace the clutch slave and master cylinders. Once the slave is allowed to fully extend, it is then virtually impossible to make it function correctly again.

Jul 08, 2009 | 1998 Volkswagen Passat

1 Answer

1999 3/4 ton ford pick up


Check the clutch slave cylinder or master cylinder for leakage and wear. If you used a 1999 in a lot of stop and go traffic, it may be time to replace the clutch.

May 03, 2009 | 1999 Ford F250 Regular Cab

3 Answers

Low / Soft Clutch Pedal, 1995 Rodeo 2W 2.6L


my rodeo had the same problem i corrected it by bleeding the slave cylinder. and is located on the driver side on the gearbox you will find it if you follow the line from the master cylinder down to the gearbox and if that helps but happens again it might have to be replaced.

Aug 01, 2008 | 1994 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

415 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...