Question about Chevrolet Cavalier

1 Answer

Need torque specs and bolt pattern for 96-2003 cavalar head gasket please send to mike@rstorage.net

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 17,970 Answers

need torque specs and bolt - zjlimited_890.jpg

Fig. 7: Location of the cylinder head retaining bolt holes





zjlimited_891.jpg



Fig. 13: Cylinder head bolt torque sequence for 2.2L engines

Tighten bolts in sequence, tighten the long bolts to 46 ft. lbs. (63 Nm) plue 90 degrees. Tighten the short bolts to 43 ft. lbs. (58 Nm) plue 90 degrees.

Hope helps.

Posted on Mar 18, 2011

  • mike39545 Mar 18, 2011

    this info was to vag and was not useful need more details and the torque pattern please help

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

03 Dodge Intrepid intake manifold torque specs top & bottom is for 3.5 V6


Lower Intake:
  1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
  2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
  3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
  4. Upper Intake Plenum:
  5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

Jun 24, 2016 | 2003 Dodge Intrepid

1 Answer

Torque spec on 21 hp briggs and strattonand sequence


Doug, Torquing multiple bolts, like on a cylinder head are shown in last video link.Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
http://www4.briggsandstratton.com/miscpdfs/RNT/Engine%20Specifications%20Chart_ms3992.pdf
FAQ Small Engine Specifications Briggs Stratton Specs
Engine mounting pattern
HOW TO LOOK UP AND TORQUE BRIGGS HEAD
How to replace Briggs Stratton Intek Head Gasket Pt 2

Jun 01, 2016 | Cars & Trucks

1 Answer

Rocker arm torque spec and intake manifold torque spec and pattern


I could not answer this any better than what I have found online. Here is a guy that has posted removal and re-installation in great detail as well as great photos.
LIM and Head Gasket Change Walkthrough FAQ GrandAmGT com Forum

I give all the credit for this answer to the poster.

Sep 12, 2014 | 2002 Pontiac Grand Am

1 Answer

Torque specs for rocker arms


The 12mm head bolts torque to 15 ftlbs.
the 10mm head bolts torque to 9 ftlbs.
crosshatch pattern for the sequence.

Jul 02, 2014 | 1992 Honda Accord

1 Answer

Head bolt torque yield


90% of head bolts are stretched when installed. If you have the torque settings, you can confirm this by checking the specs. If it says example, 90lbs feet, plus a quarter turn, this confirms they are gonna stretch once torqued.
In any case, yes, change those head bolts at all costs. DO NOT RE-USE THEM. Make sure to torque and in the order as well. do not use a random pattern when torqueing.

Nov 01, 2013 | 2002 Jeep Liberty

2 Answers

How much torque on head bolts for an 2002 grand am?


If you are ambitious enough to do your own repairs, i can't say it enough! You really need to get a repair manual they have all the information you need to do everything. Torque specs. are different for every vehical. M anuals can be had from parts stores or online in the form of downloads. Down loads are ussualy less expensive. Good luck

Aug 19, 2011 | Pontiac Grand Am Cars & Trucks

1 Answer

Need to replace headgasket


If you do it yourself you must have a torque wrench. Undo the bolts on the head cover an the head in order like shown in the picture. Be careful when removing the old gasket - not to scratch the surface, otherwise there will be leaks. You'll have to replace the head cover gasket also and other gaskets if you have removed some equipment which sits on the gasket. When you are putting everything back tighten all the bolts SLIGHTLY and then use torque wrench and torque the bolts in the opposite order as you have removed them. You will find the torque specs on the net for your car.

Jul 11, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

No problem just want to know the torque specs for the valve cover bolts on a 1977 ford f250 4x4 pk. I'm changining out the gaskets and dose not she to torque specs in my manuel.


Hi,
Rocker arm cover bolts are usually torqued between 6-9 ft/lbs, or 88-105 inch lbs. A good wrist tight using a 1/4" drive socket is how I do them and have had great success like that. Always put all bolts in finger tight, then start in the middle of cover top then go to the bottom middle across working your way outward in and up down criss cross pattern. Go around the bolts twice. Most common for people to overtighten them and then the cover will leak again. They do not need to be extremely tight, just a good snug / wrist tight......Mike

Jun 24, 2011 | Ford F-250 Cars & Trucks

1 Answer

I blew the head gasket on my 2002 Chevy Cavalier 2.2 L OHV. I am needing to know the torque specs so that I can have the gasket replaced tomorrow! A picture would be wonderful! Uncle is going to fix it but...


When torquing items today very little is done with just "numbers" in the process. Now you have to have an angle meter to complete the process so when you see me say to torque a specific number "plus so many degrees", this is how it's done. This is the meter:df03f54.gif Now, Here are the specs for installing the head:
Cylinder Head Bolt
  • First Pass
30 N·m
22 lb ft
  • Final Pass
155 degrees


Here is the sequence shown in picture form:
e8f4606.gif Also, you will need to discard the old bolts because they are "torque to yeild" bolts and CANNOT be reused. The reason: "Torque to yeild" bolts actually stretch during the torque process and once they've gone through this process they can't be reused because they no longer are able to "clamp" the head because they are too long. Hope this helps your repair project.








Oct 10, 2009 | 2002 Chevrolet Cavalier Coupe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

778 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...