Question about 1995 Oldsmobile Cutlass Supreme

2 Answers

I unhooked the cruise control pin wires where they come out of the steering colum and plug in... i need to know in what order they plug back into the 13 plug socket

Posted by on

  • cnelson753 Mar 18, 2011

    i need to know what wire goes where on the 13 flat pin plug for the turn signal and cruise control on a 97 olds cutlass surpreme.. colors would help alot...thx

×

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,168 Answers

Hello cnelson.

If you look at the connector it should be marked as to each connector number.
They may be hard to see but they should be there.
The wires for your cruise should be as follows.
Gray/black goes to connector E1, Gray to E2 , Dark Blue to E3 and Pink to E4.

If you require further help with this, leave a message for me here in comments.
Thank you for using FixYa.
KL

Posted on Mar 18, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 17,970 Answers

i unhooked the cruise control - zjlimited_889.jpg

Fig. 18: 3.1L (VIN M) and 3.4L (VIN X) engine control wiring diagram - 1996 vehicles

Posted on Mar 18, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Pontiac g6 cruise control does not work 95% of time


The most common issue here is the rotating contact under the steering wheel called the "Clockspring" has an open printed circuit ribbon. To change this requires the Airbag and steering wheel be taken off. You must disarm the steering wheel mounted Airbag before work starts, failure to do this can kill you. Read and follow the service manual instructions to the letter.

Apr 25, 2016 | 2007 Pontiac G6 GT Convertible

1 Answer

Cruise control not working 1990 k1500 4x4 cruise control not working were are all the parts located and what to look for


take the cover off the cruise control actuator located on the firewall in engine compartment remove the cover and see if the ribbon is broken that actuates the cable to the throttle,then ck the brake switch adjustment,if all is ok the switch on steering colum is bad to replace this you grasp the whole handle firmly and rotate it toward front of veh while pushing in toward colum,the wires go through the colum and are attatched under dash,attatch a fine stiff wire at connector and pull out then attatch thin wier to new switch wire and pull back through colum

Sep 22, 2014 | 1990 Chevrolet K1500

1 Answer

Where to plug the cruise control back in from switch


Remove the covers below the steering column. Locate the wiring harness mounted to the steering column. Follow the wires toward the steering wheel. You should be able to locate the separate 3 same size wire harness for the cruise control. The wires from the switch handle run alongside, on the inside of the column with your turn signal wires.

Apr 22, 2014 | 1978 Chevrolet Corvette

1 Answer

Cruise control just stopped working after I had a brake job done is this related. How do I go about checking it out , I have had it scoped it was inconclusive. Do we have to take apart the steering colum.


I would check the cruise control cables and the unit, make sure everything is plugged in and connected. Also check the vacuum hose, if so equipped. If you have to replace to cruise control switch, I believe it involves the steering wheel and column. A repair manual maybe helpful with locations and testing procedures. Hope this help you.

Mar 08, 2010 | Buick Regal Cars & Trucks

1 Answer

1991 buick regal, i need instructions on how to replace a ignition switch


key switch,remove center cap and pull steering wheel off with wheel puller.disconect horn,blinkers assembly.push pin remove ignition. ignition switch, remove panel under dash un bolt steering colum lower to seat un screw ignition from top steering colum un hook rod,un plug harnees put new one on put back together

Feb 02, 2010 | Buick Regal Cars & Trucks

1 Answer

Cruise control doesnt work,,,i there any fuse for it? this is for a cadillac deville 94


Cadillac's of this year have been known to have the wire(s) fromt he cruise control break in the steering colum. This is due to the tilt wheel moving up and down over the years. You should be able to either repair the broken wire or get a used unit (turn signal/cruise) and wiring harnes at a salvage yard. The wiring runs along the steering column to a connector on top of the column about half way down.
Check your fuses first. I believe the cruise and a couple of other accessories are on the same circuit. Is there anything else that doesn't work? (i.e. cigarette lighter, dome lights...) If you have the owner's manual that would help OR a trip to the public library in the auto section...Hope this helps.

Nov 19, 2009 | 1994 Cadillac DeVille

1 Answer

I removed the tilt steering colum housing to instal a new cruise


The plastic piece goes between the steel rod and cruise/wiper lever. You will have to remove the wheel and the upper bearing housing to get it back where it goes. If you put some wheel bearing grease on it then it will stay in place during reassembly.. Good Luck

May 15, 2009 | 1986 Chevrolet El Camino

1 Answer

Cruise control, and horn do not work + air bag light came on


You need what is called a clock spring. It is located behind the steering wheel. Some of these had a recall on them. Check with your dealer to find out.

Feb 15, 2009 | 1998 Plymouth Voyager

1 Answer

1994 Ford Taurus Station Wagon Steering Coulmn Wire Harness


i need to know to how to remove the power steering bracket on a 1994 ford taurus 3.8

Sep 23, 2008 | 1994 Ford Taurus

1 Answer

Cruise control


My guess is that you have a short in the steering colum.

Eitan.

May 30, 2008 | 1999 Ford Taurus

Not finding what you are looking for?

Open Questions:

See all 1995 Oldsmobile Cutlass Supreme Questions

1995 Oldsmobile Cutlass Supreme Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...