Question about Chrysler Town & Country

Open Question

Chrysler trouble codes p0700 and p1776 and p0734 for 2000 town and country 3.8l

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
dsacco86
  • 1077 Answers

SOURCE: check engine light on 2005 town and country 3.3

(DTC) CODE # P0700....Transmission Control System (MIL Request)

Translation:
Transmission Control Module (TCM) Malfunction or Failure.

P0700 Information Code

The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.

This code is for information ONLY. If this code is present, check for transaxle codes.


P1776: Solenoid Switch Valve Latched in Low/Reverse Position. The TCM monitors the L/R solenoid to ensure that the fluid transfer happens. It uses a Pressure switch to verify this. Usually this code is set by a switch that is stuck or a solenoid that is not mechanically operating.

A transmission shop would be better suited for this type of work.

Posted on Apr 11, 2009

Ad
  • 412 Answers

SOURCE: MY 2004 CHRYSLER 300M CHECK ENGINE LIGHT CAME ON

p0700 indicates you have trans fault present..p1776 is a trans fault which means solenoid switch valve is latched in low/reverse position..solenoid switch valve is located in valve body of transmission,but for 2001-2004 LH vehicles you need transmission event data read to find out what TRS position the fault set..recommend chrysler dealer for this fault..also build code on solenoid pack in trans must be checked..if in a certain build code range,you replace solenoid pack..not the valve body..valve body must be removed to check build code on solenoid pack..i have seen this problem before..i am a dealer technician, and had one of these fault codes last week and solenoid pack was the problem..solenoid pack is about 375 dollars..total time with diagnostics was about 3 hours..

Posted on Jun 14, 2009

alicantecoli
  • 22156 Answers

SOURCE: Chrysler trouble code U110C on 2005 chrysler town

encrypted software ,dealer only----yes i know you are showing a reading but it doesnt mean anything or if it does it shows a different code .so your snap on or mac tools scanner is a waste of time and money.Nearly all new motors from 2005 are using encrypted software to stop general mechanics like me from working

Posted on Sep 12, 2009

roniecon
  • 6826 Answers

SOURCE: Chrysler town & Country 1998 computer code is

The power control module is most likely bad.

Posted on Jan 19, 2010

  • 149 Answers

SOURCE: Trouble codes on a 2000 Chrysler town and country

0775 is Presure Control Solenoid "B", 0784 is 4-5 Shift these are trans codes from the transmission Solenoid. This is a changable part for any mech. Part is around $200 & includes the gasket.

Posted on Jan 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 chrysler town and country limited 3.8litre where is the transmis 2003 Chrysler Town and Country limited recalls 2003 Chrysler Town and Country limited 3.8litre code p1776 how can I fix


It is not a do it yourself fix.

This is an automatic transmission issue which may involve replacing the valve body and solenoid pack and affects transmissions fitted to various Chrylser models. It could also be a symptom of more serious transmission problems and requires proper investigation and diagnosis.

On some models there was a Technical Service Bulletin issued to dealers on this problem .

Dec 15, 2015 | Chrysler Cars & Trucks

1 Answer

Why my 2001 town & country 3.8 will not shift gears?


p1784 shift up /down wire open,,,P0700 Transmission Control System Malfunction

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com

P0732 Gear 2 Incorrect ratio

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com

Apr 23, 2015 | 2001 Chrysler Town & Country

1 Answer

What does emission codes P1776 and 0700 mean for a Chrysler Town and Country?


P0700 is a generic trans
control system malfunction code, P1776 seems to be - Solenoid switch valve stuck
in L/R position or Gearbox Ignition Retard Request Timeout Fault.

Jan 14, 2013 | Chrysler Town & Country Cars & Trucks

1 Answer

Error code 0700 aa1 aa2


Hi there:
The DTC P0700 is a Information Code The Transaxle Control Module (TCM) that monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.
This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it, which can only be done with a diagnostic scanner. The self retreival method for chryslers with the ignition key will not pull up the specific transmission fault codes in the TCM.


Hope this helps.

Mar 30, 2012 | 2001 Chrysler Town & Country

1 Answer

I have a chysler town and country the engine light came on, I had it tested the codes were 700 and 1776 what do they mean


ok your p0700 code is '' transmission control system malfunction '' and your p1776 code is '' solenoid switch valve latched in the LR position " they seem to go hand and hand on many chryslers from what ive seen.

Nov 07, 2011 | Cars & Trucks

1 Answer

Engine code reads P1776 1/2 and P0700 transmission


P0700-This Relates to MIL"Malfunction Indicator Lamp")( Request - Control System for Transmission
unable to locate description for P1776,can you get all systems scanned for codes again as 0700 just indicates that a fault has occurred that has lit the check light and logged at the ECU.
Obviously it will be related to the shift fault,maybe a speed sensor or a dirty fluid fault.
Get back to me with any extra info.

Apr 10, 2011 | 1998 Chrysler Town & Country

1 Answer

2005 Chrysler T+C Van drives fine but has P1776 and P0700 codes - I have the descriptions. One piece of information i came acros points to the easy replacement of a $6 solenoid, though no details are...


The only thing I can suggest is to replace the $6 solenoid and reset the codes by disconnecting your battery for a few minutes and see if it codes up again. I think that may at least clear the P0700 (Tansmission Control System Malfunction) and if P 1776 comes back - then perhaps a transmission shop needs to look at it. Let me know how it works out. Thanks.

Jan 08, 2011 | 2005 Chrysler Town & Country

1 Answer

Check engine light on 2005 town and country 3.3


(DTC) CODE # P0700....Transmission Control System (MIL Request)

Translation:
Transmission Control Module (TCM) Malfunction or Failure.

P0700 Information Code

The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.

This code is for information ONLY. If this code is present, check for transaxle codes.


P1776: Solenoid Switch Valve Latched in Low/Reverse Position. The TCM monitors the L/R solenoid to ensure that the fluid transfer happens. It uses a Pressure switch to verify this. Usually this code is set by a switch that is stuck or a solenoid that is not mechanically operating.

A transmission shop would be better suited for this type of work.

Apr 11, 2009 | 2005 Chrysler Town & Country

1 Answer

I want to know what trouble code P0700 means in a chrysler town and country 1998, and how do I reset the check engine light?


0700 is a "transmission control system malfunction". The entire 0700 series of codes deals with transmission trouble codes in more detail so the 0700 won't tell you much unless one or more of the other codes also were set.

Jan 10, 2009 | 1998 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...