Question about 1989 Ford F 250

1 Answer

WANT CHANGE OUT OF LOWE GEAR - 1989 Ford F 250

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 115 Answers

It could be one of a few things.

1. I would check my linkage to make sure the adjustments are proper. (you could be putting the truck in drive but it is actually in low gear) The easy way to check is to get under the truck, and watch the linkage on the side of the tranny while someone is in the truck moving the lever to drive and watching that the linkage is correct.

2. If that is ok, then replace the modulator switch.

3. If these don't work you have a problem internally in the transmission.

Posted on Mar 18, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Oil light on while running


Normally, the oil light indicates low oil pressure, usually due to lowe oil level. That being said, is you have a constant oil light with the engine running and you are not getting clacking noises from the valves, you may have a defective oil sender. Regardless, it is not worth destroying the engine to find out. You should immediately shut the engine and check the oil level. If it is very low, add oil and retest. If the fault persists, attach a mechanical oil pressure gauge to the engine. If the pressure is normal (usually 30-45 psi), then change the oil pressure sensor. If the oil pressure is less that 20 psi, you should investigate the oil sump and pump for problems.

Oct 04, 2015 | Cars & Trucks

1 Answer

My Dodge caravan run great but slips out of drive and wont go out of 3rd or second gear , and it didnt help , It shifts fine otherwise and doesnt always happen . when it does it wont go back into lowe


There should be a tensioner for the shift lever in the transmission, that help keep the car in the gear you put it in. Check the shift cable or linkage, you may have a issue there. If all that checks out sounds like a internal issue, and most likely would set a code in your computer

Jan 10, 2015 | Dodge Cars & Trucks

1 Answer

My 90 dakota dies at lowe speed when wether is cool,whay ??


Is your check engine light 1) Working 2) On? One suspect would be the coolant temp sensor; which tells the computer the ambient temperature so that it can make appropriate fuel adjustments .... though I'm a little unconvinced that it it would have enough effect to cause stauling.

May 09, 2014 | 1990 Dodge Dakota

1 Answer

My 87 ford Turbo Coupe has a difficult time going into 3rd all other gears are fine


sounds like its bulk rings in gear box, they spin the gears ready as u change gear when they wear the gears are not spun enough to select u probably need to over hall gear box , to help u change gear for now double d clutch, whats this as u want to change gear push clutch down move out gear release.. clutch pushdown again put in to gear use this with each gear un need to change what this does is spin gear ready for u as if bulk ring had done it for u if u are good u can just change gear but have to b good for this

Nov 12, 2013 | 1987 Ford Thunderbird

1 Answer

1999 2.5 ranger motor normal temp if you accelerate and shift at a mid range to high rpm when you inter the next gear it appears to be loaded up ot skipping then it clears up and the same thing happens...


Do a compression check on the cylinders. while you're taking out the spark plugs check them for soot and oily deposits.
Scotty Kilmer has just put a video on you tube that explains this a little. the only thing is i don't know what the spec psi is for this engine

Aug 21, 2013 | Ford Ranger Cars & Trucks

1 Answer

How do I change a piston rod for a 2001 pontiac grandam?


remove engine from car and install on an engine stand, remove head and oil pan, disconnect lowe rod bearing cap and remove piston through the top, measure crank with a micrometer to get proper bearing size, install rod onto piston and install using ring compressor then install on crank shaft, lube well, reassemble engine and install in car

Feb 12, 2011 | 2001 Pontiac Grand Am SE

1 Answer

On a 92 S-10 p/u, how do I remove the dash in order to repair dash lights that are out?


Well if there are no visible screws then it probibly snaps in.Not sure what year they started doing this but my 95 full size if you have a automatic trans set the parking brake and set the gear selector in L or 1 and grab the dash above the steering wheel and start pulling there and work your way around.My 85 S 15 had a dozen screws all around the out side of the dash so not sure.If you have tilt wheel you will need to lowe it all the way down. Well hope this helps and good luck.

Jun 10, 2010 | 1992 Chevrolet S-10

1 Answer

Enigne wont start after it died on road


fine metal shaving means major engine damage, time for a tear down , start with the oil pan, find metal in there which you will, the damage is extensive, time for a rebuilt

May 13, 2010 | 1986 Toyota Tercel

1 Answer

How do you change the antifreeze on the radiator?


Two ways to drain the radiator..
There is a drain plug on the radiator - inside - bottom corner - usually on drivers side..
OR - pull off the lowe hose..

Hope this helps !!
Rate me good ;o)

Jul 13, 2009 | 1998 Oldsmobile Cutlass

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...