Question about Mercury Tracer

1 Answer

How hard is it to remove the transmission on a 1993 Mercery Tracer 1.9 4 cyl. car from the engine to change out the front seal.

Posted by on

1 Answer

I wouldn't suggest you try it in your driveway
You really need a lift

Posted on Mar 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE A 1999 MERCURY TRACER THE TRANSMISSION MOUNT BRACKET IS IN THE WAY TO GET THE TRANSMISSION PAN OFF ANY IDEAS??


sometimes its easier to use a engine lift and just loosen the motor mounts and ****** mount and lift the motor and trans just enough to remove the pan but makesure you dont lift to much as to hit the firewall or underside of the car.

Sep 20, 2012 | 1999 Mercury Tracer

2 Answers

How hard is it to seal the front seal on the transmission


Front Pump Seal that the Torque Converter goes into?

You have to remove the transaxle to do that

Jul 02, 2011 | 2001 Ford Taurus

2 Answers

Change front main seal , leaking oil around timing chain cover. could be seal around harmonica balancer.


yes, I just changed one of these recently. Had to take both front and bottom off engine. Very difficult repair, as there are no good jack points for the engine when you have all the motor mounts off.
Here is procedure I would recommend.
Remove starter and engine to transmission brackets front and back.
Remove transmission starter gear cover.
drain oil and remove oil pan.
put a block under the crankshaft and jack to release weight on motor mount.
remove front motor mount (by serpentine belt)
remove belt.
remove compressor and bracket.
remove crank pulley and vib damper.
remove timing cover. mark timing belt with direction of travel
loosen tensioner gear.
remove timing belt.
remove crankshaft timing gear and key.
remove seal and oil pump housing.
clean gasket surfaces.
replace seal and reverse procedure.

If you have questions, let me know.

Oct 06, 2010 | 1993 Dodge Caravan

1 Answer

Transmission fluid is pouring out between the transmission and engine is this a front seal leak?


Yes, it could be the front pump seal or even a cracked front pump ,either way the tranny has to come out.

Dec 26, 2009 | 1994 Mercury Tracer

1 Answer

1995 jetta 4 cyl. trans fluid coming from bell housing. possible converter seal? I was told it's necessary to remove engine and trans together. is this true? first vw repair for me. thanks


It is most like the front pump seal, or converter seal. You can remove the transmission without removing the motor. It's a tight fit.

Jun 13, 2009 | 1995 Volkswagen Jetta

1 Answer

Trans leaking fluid


it is hard to make a mistake when looking at a front seal leak so your diagnosis is probably correct. As for the repair it is pretty labor intensive as the transmission needs to be completely disconnected from the engine and at the very least slid back 8 inches or so (its easier to change the seal with trans completely removed) to acess the front seal to change it

Mar 19, 2009 | 1991 Dodge Power Ram 50

3 Answers

Distributor cap firing order 1993 chevy cheyenne truck v6


Firing order is 1-6-5-4-3-2 cyls. # 1-3-5 on drivers side front to back and cyls. # 2-4-6 passenger side front to back.

Nov 28, 2008 | 1989 Chevrolet C1500

1 Answer

Water pump


Once you remove the timing belt covers,rotate engine,by hand via cranckshaft bolt (only in direction of normal engine rotation,i believe clockwise on that) and aligne all timing marks. At this time your engine is at #1 tdc..Follow manual and change belt.....Good Luck!!!

Sep 14, 2008 | 1993 Dodge Spirit

1 Answer

Front Main Seal is blown on the Transmission


You have to remove the transmission, remove the torque converter to access the seal. Most likely the bushing behind the seal is worn out allowing fluid to leak past the seal. After the trans. is out, take it to a trans. shop. It requires a special tool to change the bushing. Seems like a bunch of work for $10.00 in parts. The rear main seal requires pulling the pan to access it. When the trans. is out, this is the time to replace the rear main seal on the engine.

Jun 10, 2008 | 1993 Ford Explorer Limited

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...