Question about 1999 Toyota Camry

1 Answer

Shifter cablebroke goingfromdrive to park how much for a new cable

Posted by on

1 Answer

Go to the dealers parts counter and ask

Posted on Mar 18, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What could be wrong with my 2006 Hummer h2 that has no foward or reverse gear sand when in Park its still in nuetral?


check the linkage,... look at shifter cable bushing most likely missing, or rotten. there is an aftermarket bushing by Dorman part 14055 about 12 bucks or a new cable around 65.00 plus2 hours labor. Also bushing fix has something on Ebay 25.00 an ez install bushing. I put new cable on mine and repaired old cable w/ new bushings for next time. Very common problem Good luck all

Jun 14, 2014 | Hummer H2 Cars & Trucks

1 Answer

Put a new engine in a 1998 isuzu rodeo now it won't start. I thought it was the neutral safety switch because the R was on the dash and it was in park


This could be the problem. If your dash indicator is showing reverse but the transmission is in park it could be the safety switch. I'm not talking about the safety switch in the transmission though. In automatics they put a second switch to kill the starter from engaging. You need to adjust the linkage. If your shifter isn't actually on the column but the indicators are there is a cable that attaches the floor shift to the column and that is adjustable. Put the Floor shifter in Park and turn the column section nearest the dash by hand until you find park. Then adjust the cable length as needed. If all you have is the column shift it is still a cable adjustment. Set the emergency brake, drop the shifter to low 1 and adjust the cable linkage by loosening it on the transmission and manually move it all the way to low 1 then tighten it down then move the shifter to park and repeat teh adjustment process to verify that it is properly aligned. Lock the linkage back down and see if the vehicle will start, if it doesn't move the shifter to neutral and try to start the vehicle if the vehicle starts then check the column shift safety switch at the park position to make sure it is still in place and working. Typically, if the vehicle won't start in Park or Neutral it is more likely to be the Transmission neutral safety switch.

Nov 15, 2011 | 1998 Isuzu Rodeo

1 Answer

I have a 2004 GMC Envoy the shifter cable came off and I had to put it in park myself. I noticed at the end of the shifter cable that the round plastic washer at the end of the cable broke. How can I find...


Check out this site for the part to fix the transmission end of the cable. Go to the rear end of the transmission on the driver' side (under the car/truck). Make sure to push the transmisssion lever toward the front of the car/truck (park position), the shifter should also be in park. Get the part, install is easy.

http://www.atfbilletparts.com/shifter-cable-repair-kits-by-veh-gmc-vehicles-c-208_219/92-09-gmc-envoy-shifter-cable-repair-pin-p-569

Oct 27, 2010 | 2004 GMC Envoy

1 Answer

How do i adjust the shifter linkage on my 1981 blazer.It shifts into drive but not 2nd or 3rd


I will try to help.
I would get someone to shift the shifter inside to the park position to see the direction underneath of the
shifter on the tranny. Then loosen the cable to the
shifter on the tranny move the shifter on the tranny to the same direction you seen toward park to the last position on the shift mechanism. That should be the park position. now put the shifter in the park position and tighten and/or reattach the cable. you should be good now. Hope this helps

Feb 10, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

My 1999 Chevy Blazer wont go into park


secure vehicle with chocks and set parking brake under vehicle check on drivers side of transmission selector control look at cable for binding or damage the cable snaps into place if looks good remove cable and try to put selector shifter into park[ if it goes in and stays than look back under vehicle and try to match up selector and cable.not reaching and trans selector in park adjust cable and reconnect try shifter for park] -if shifter doesnt go into park than check on dash plastic selector lock may b worn or damaged, if above is fine and selector/shifter is not problem than problem is internal inside transmission park rod damaged or broke good luck and thanks for using fixya

Oct 13, 2009 | 1999 Chevrolet Blazer

1 Answer

94 Honda Accord-Automatic shifter stuck in park


i had the same problem there is a shift link cable that runs to the trans i think...the cable has a kink in it or somthing you need to go and buy a new cable for about $100 it will run alot smoother ..

Jul 04, 2009 | 1993 Honda Accord

3 Answers

I'm having trouble moving the shifter


If you're on an incline, that will affect it. Try setting the park brake prior to shifting to park. Also there is a cable/interlok safety system that prevents shifter movement out of park without the brake pedal being depressed, that may need adjustment. Also check under the hood see if the shift selector cable is routed close to the exhaust, it could be melting. And maybe the selector cable needs adjustment.
Good luck with that and let me know if there is anything more I can help with.

Apr 05, 2009 | 1999 Chrysler 300M

1 Answer

Difficult to move shifter automatic trans


need to check to see if there r any recalls for ur vehical, sounds too new for this problem, also it could be that u need a new shifter cable....
Try disconnecting cable at the trans and see if it move easyer, if it does than trans problem....in ternal

Feb 09, 2009 | 2006 Ford Mustang

1 Answer

Car Won't Fully Shift into Park


You either have problem with the shifter assy, or the shifter cable has come out of adjustment.
If you remove the shifter bezel and center console you will be able to see the shifter cable. There will be a white or black lift tab on the cable. Release the tab and and place shifter in park. If it still does not go into park that means that you will need a shifter assy. If it goes into park with the tab released you push the tab back down with it still in park.

That should take care of your problem.

Aug 29, 2008 | 2004 Chrysler Sebring

Not finding what you are looking for?
1999 Toyota Camry Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...