Question about Mercury Grand Marquis

1 Answer

Lamp over my license plate not working what is the fuse number?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

That lamp is on the same circuit as the tail lights. The bulb may have failed.

Posted on Mar 18, 2011

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
eitan
  • 291 Answers

SOURCE: changing license plate lamps on the tracker

There's no need to take the whole back panel off to do it, the light cover on the bulb twists out, and it might take some elbow grease to twist it, then the bulb is easy to change.

Good luck,
Eitan.

Posted on Jun 10, 2008

  • 226 Answers

SOURCE: License plate lights do not work.

The licence plate lights are in the same line as your tail light wiring assembly. I assume your tail lights are working or you would have got a ticket for that. The wire is either cut, broken or unhooked from the tail light wires (which usually are brown). If you can not find the problem, you can always run a new wire to the tail light wire from your licence plate wire. Then they should work.
Your other problem is that the license plate ground is rusty & not grounding, which would also not let them work, so you should probably check that first. Rick

Posted on Apr 14, 2009

  • 25 Answers

SOURCE: license plate lights not working.

check and see if u have power at socket

Posted on Jun 25, 2009

  • 1348 Answers

SOURCE: taillights and license plate lights not working

there is a short somewhere.put a test light in place of the fuse.
the light will glow bright.when the short is removed,the light will go dim

Posted on Jul 18, 2009

  • 1 Answer

SOURCE: can't get rear license plate lamp covers off

The manual says switch off the lights and disconnect the battery. Then "Open trunk lid. Press and slide license plate light outward and remove". The photo shows that there is a clip on the side of the light away from the center, and a notch that fits the body on the side towards the center. So what you are doing is pushing the light holder towards the side of the car far enough to compress the clip and get the notch past the metal, then the inner edge of the light hold should lift out. To install, just put the notched end in first and the press the outer edge until the clip snaps into place.

Posted on Aug 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which fuse is for the license plate light?


There isn't a fuse for just the license plate lights , do your park lights work ? The park lamp relay powers the license plate lights as well as the parking lamps .

Dec 16, 2015 | 2003 Chevrolet Impala

1 Answer

2007 chevy equinox license plate light won't work after bulb and fuse replacement


Do the park lamps work ? license plate lights get power from same fuse ! Check ground wire ! use a volt meter an do voltage drop test ! Voltage Drop Testing The fuse for the license plate lights is in the under hood fuse box -engine compartment ! fuse #12 RT PRK LAMP 10Amp .

May 23, 2015 | 2007 Chevrolet Chevrolet Equinox LT

1 Answer

Need to replace fuse for license plate bulbs for 2010 Ford Edge SEL....What fuse number is it?


normally the number plate light is on the same fuse as the park lights . I would be looking for a fault in the number plate area ( broken wire or blown bulb or bad/ no earth)

Dec 06, 2013 | Nissan Quest Cars & Trucks

1 Answer

Number plate fuse


Took me a minute to figure out what "number plate" is.
Normally the license plate lamp circuit is on with the tail lamp circuit.
So if the tail lamps work the problem may be in the wiring.

Apr 19, 2013 | 2004 Toyota RAV4

1 Answer

Where is the fuse for the plate number light ford escape 2003


I have found that the cars with which I have experience use the same fuse for the license plate light as is used for the tail lights. Not sure why or if yours is different.
So, if the tail lights work and the license plate light doesn't, then the problem can usually be resolved by confirming that the wire is properly connected, cleaning the contacts and replacing the lamp.

Dec 25, 2012 | 2003 Ford Escape

1 Answer

Where is the fuse for the license plate lamp located


I'll tell you where the fuse is but I want to mention that if it is just the license plate lamps that are out you may have other problems. The fuse you are looking for also controls the power to the left & right back up lamps, the right park & stop lamps and I think the left turn signal but don't quote me on that. So as you can see this fuse covers more then just the lamps for the license plate. Anyhow the fuse you are looking for is in the fuse box located to the left of the steering wheel by the brake pedel. It is in the number 7 position (see picture below) and is a 15 amp blue fuse. I hope this helped and good luck.

clifford224_54.jpg

Feb 21, 2011 | 1999 Ford Windstar

1 Answer

Tag light is not working. is there a fuse that will get the light turned back on?


The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:
  1. Remove the two mounting screws from the license plate lamp.
  2. Remove the license plate lamp from the rear bumper fascia.
  3. Remove the license plate lamp socket by turning it counterclockwise.
To Install:
  1. Install the license plate lamp socket by turning it clockwise.
  2. Position the license plate lamp to the rear bumper fascia.
  3. Install the license plate lamp mounting screws.

Feb 17, 2011 | 2004 Chevrolet Impala

1 Answer

License plate lamp doesn't work after replacing


Have you checked for power at the socket? But most vehicles do have 2-3 fuse panels; in different locations.

Jan 26, 2010 | 2005 Chrysler Pacifica

1 Answer

2007 Pontiac G6. Rear license plate bulb socket dead


park lamp and license plate share same fuse.check park lamp fuse.if fuse good you have ground wire problems.

Nov 30, 2009 | 2007 Pontiac G6 GT Convertible

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...