Question about 2000 Jeep Cherokee

1 Answer

I replaced ignition coil in to new for jeep grand cherokee 1999 4.0i limited and engine not whant to start up but then i put back old one it starts and works just one cylinder not working.any ideas?

Posted by on

  • stiklineakis Mar 18, 2011

    oh well i passed that coil pack to test for car electrition and if it not working the shop will send it back to jeep centre thanks for help prostreet 55. i found some info how to check if coil pack is working here you if it is right info

    Put on your safety glasses and open the hood. Disconnect the negative cable from the battery and place it out of the way so that it will not make contact with the battery terminal while you work.

    2
    Locate the coil pack. The coil pack is a long black unit, bolted directly on the cylinder head on the left side of the engine. The coil pack attaches directly to the spark plugs.

    3
    Remove the four coil pack mounting bolts using a ratchet.

    4
    Pry the coil pack away from the engine head. Grasp each end of the coil pack and work it back and forth until you can remove the coil pack boots from the spark plugs.

    5
    Lift the coil pack up slightly until you gain access to the electrical connector on the back side of the unit. Depress the clip on the electrical connector and unplug it from the coil pack. Remove the coil pack.

    6
    Place the coil pack on a flat surface.

    7
    Turn on your ohmmeter and set it to the 20,000 ohms range.

    8
    Touch the ohmmeter leads to the connectors in the first spark plug boot. Your meter should read from 6,000 to 30,000 ohms. Repeat this on each spark plug boots. Replace the coil pack if the measurement falls outside of this range.

    9
    Set the ohmmeter to the 10 ohms range. Touch the center prong on the electrical connector with one of the leads and the first spark plug boot with the other. Your meter should read less than 2 ohms. Repeat this while touching the second lead to each spark plug boot. Replace the coil pack if the measurement is higher than 2 ohms.

    10
    Replace the coil pack with a working coil pack, if necessary. Reinstall it following the removal procedure in reverse



    Read more: How do I Check a Jeep Grand Cherokee Coil Pack? | eHow.comhttp://www.ehow.com/how_7433253_do-grand...

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Contributor
  • 299 Answers

Is it a single coil or a coil pack with all plug wires going to it..if its a coil pack its bad and the new one is no good ,that does happen alot more than u might think. i had a brand new MSD box bad from factory. and that was like 200 bucks so you never know. they have tests that u can do on the coil also to c if that is problem let me know if u want to go that way and i can help also

Posted on Mar 17, 2011

Testimonial: "thanks so i could send back to them and get my money back."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1996 Jeep Grand cherokee with the 5.2l v-8 engine. Last week I started it, and it ran for about 1 minute before shutting off. The engine cranks, but no ignition. I replaced the Crankshaft position...


Time to meter voltage. Start with the 12V circuit. Are you getting voltage at the coil. Does the voltage fluctuate when the engine cranks? If yes to both check the high voltage circuit. Start with the coil then the distributor then each plug. You should be able to find where the spark is failing.

Sep 07, 2014 | 1996 Jeep Grand Cherokee

4 Answers

96 jeep cheokee problems no spark


I would make sure you have voltage to the coil. Could be a fuse or relay problem. Is the check engine light on when you turn the key on ?

Aug 16, 2012 | 1996 Jeep Grand Cherokee

1 Answer

No fire from coil- 1990 jeeo cherokee replaced coil, ignition module and coil pickup, what is left?


are you getting power to coils, if not it could be the ignition switch, one major sign of a bad switch is dash lights go off. vehicle may crank but not start,no current to fuel pump, stalling, failure to start.

Check the MAP sensor. To see if this is the problem, assuming that the Jeep won't start but is turning over, unplug the MAP sensor and then plug it back in. If you can start it now, the MAP sensor needs to be replaced. The MAP sensor is located in the engine compartment, where the firewall meets the body at the top of the engine compartment, on the driver's side. Good luck. check map sensor first!


Feb 13, 2011 | 1990 Jeep Cherokee Limited

1 Answer

Jeep cherokee limited ed. 96 wont start


check for spark??...and ignition coil

Mar 11, 2010 | 1996 Jeep Grand Cherokee

2 Answers

My 1997 Jeep Grand Cherokee cuts off while I'm driving.


If you have zero oil pressure thats a BAD sign, first have a mechanic check what the engines actual oil pressures are.

Oct 31, 2009 | 1997 Jeep Grand Cherokee

1 Answer

My 1995 jeep grand cherokee limited is not starting, changed ignition coil,rotter and cap gave a full tune up and still nothing happend,is it the computer?


There is a known problem with the 'neutral starting switch' that has occurred in two of our several Jeeps. Try starting it in neutral and park both and 'jiggle' the selector while you are doing it.

Jul 24, 2009 | 1995 Jeep Grand Cherokee

2 Answers

96 grand cherokee crank no start, no spark from


have the crank sensor replaced this controls the spark and injector pulse it is located on the drivers back side of the engine above the transmission housing!

Jun 08, 2009 | 1997 Jeep Grand Cherokee

2 Answers

99 grand cherokee laredo wont start but turns over


Check power to the ignition coil,,you may have interfered with one of the wires going to the coil

Jan 16, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Cherokee Logo

540 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...