Question about Ford Probe

1 Answer

Need timming marks for 1995 Ford Probe - Probe Ford Cars & Trucks

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Get the #1 piston to top dead center ( all the way up ) then you can buy a strip that sticks the the dampner or harmonic balancer and put the zero where the pin or tab is and there you go

Posted on Aug 02, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you replace a distributor on 1995 ford probe

you should just have one hold down bolt maybe two,pull out distributor.make sure you put it in the same way it come out or your dist timing will be off.


Dec 06, 2010 | 1995 Ford Probe

1 Answer

I need to know if the plug wires at the front go on the top of the distributer or bottom and what order

since you did not say the engine size this website gives a diagram, hope it helps Tim:

Nov 01, 2010 | 1995 Ford Probe

1 Answer

Would open vacume lines cause feul smell in the cab 95 ford probe gt

no,you need to check your fuel lines and filter.


Oct 23, 2010 | 1994 Ford Probe

1 Answer

1995 ford probe new engine no spark

did you install the crank sensor?

Mar 23, 2010 | 1995 Ford Probe

2 Answers

How do you replace a distributor assembly on a 1995 Ford Probe GT

There is one bolt and clamp at the bottom of the distributor shaft.
You MUST make a mark on the shaft AND the engine so that when you put another one in, you can line it up correctly.
Otherwise, your spark timing will be off & may not run.
When removing you may have to twist the assembly as you remove it (that's normal).
Oh,, yeah... don't remove the spark plug wires at the distributor .. until you really have to... mark them well (masking tape or whatever technique you use).

Sep 01, 2009 | 1995 Ford Probe

1 Answer

95 probe 2.0 stalls now wont start

there are a couple of small relays on your fire wall that could be giving you grief. try replaceing those.

Feb 08, 2009 | 1995 Ford Probe

1 Answer

How do you set the timing marks on 97 ford probe?

what marks are used when setting timing on 1997 ford probe

Oct 19, 2008 | 1997 Ford Probe

2 Answers

1995 Ford Probe GT no spark

Hi is your Probe a 2.5cc 24valve.If it is then you may need to check the CPS(crank position sensor) All the best.Phil

Aug 17, 2008 | 1995 Ford Probe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5648 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides