Question about GMC Sierra 1500

Open Question

Disquicked battery and hooked battery back up now my astrostart dosnt work

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can I connect a astrostart remote key to my '08 Chevy uplander?


you need to notify astrostart since their are 4 different types of systems and give them the information on all the specs for your vehicle and they will advise how much and what additional components are needed

Jun 29, 2016 | 2008 Chevrolet Uplander

1 Answer

I have an Astrostart hst5224, It will star then immediately shut off. My jeep is A manual transmission


[PDF]MODEL RSS-5225 - DirectedDealers.com

www.directeddealers.com/manuals/OG/Astrostart/RSS-5225_OG-Eng.pdf
Immediately report any malfunction to the AstroStart dealer that performed the ... Always turn off the main switch when not using the remote starter for .... The startmodule will inform you of the status of door locks, the alarm and of the engine. .... If the trunk is opened for more than 5 minutes, the system switches to the.

How do you reprogram an AstroStart remote HST5224

www.answers.com > Wiki Answers > Categories > Cars & Vehicles
In order to reprogram an AstroStart HST5224 remote, you must putthe key in the ignition ... lamp) b, press and hold UNLOCK button, after 1 second key LED will flash once c, .... C. Turn the ignition to ON (Do NOT Start) then back to OFF. ... B.Immediately after letting go of the lock and unlock buttons, press the lock button by ..

Nov 24, 2015 | 2007 Jeep Wrangler Unlimited Rubicon 2...

2 Answers

Astrostart won't start the car


You may need to reset the system.

SEQUENCE ACTIVATED BY THE PARKING BRAKE .
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply the parking brake Once Twice
Note: The system can be set - at time of installation - to require that the parking brake be applied once or twice.
If set for two actuations, pause one second between the two.
4. Remove key from ignition (the system keeps the engine running).
5. Exit the vehicle.
6. Within 60 seconds, close all doors.
7. The system will stop the engine and blink the parking brakes once to confirm the sequence is valid (vehicle is
ready for a remote start command).
SEQUENCE ACTIVATED BY THE REMOTE CONTROL
1. While engine is running (key in ignition switch), apply the brakes and hold the pedal down.
2. Move gearshift lever to neutral.
3. Apply parking brake.
4. Send the start command (Model 801 & 2101 - Model 903 ).
5. Remove key from ignition (the system keeps the engine running).
6. Exit the vehicle.
7. Using the remote, send the STOP command. The system will stop the engine and parking lights will blink once
to confirm that the sequence is valid (vehicle is ready for a remote start command).
http://www.astrostart.com/Support/Guides.aspx

Nov 27, 2012 | Cars & Trucks

1 Answer

I have an astrostart remote hst5224 that has a new battery and it beeps...but nothing else


This remote can operate up to four different vehicles, the default is 2, make sure you are in the correct mode. This is changed by pressing the "P" button on the back of the remote for two seconds, each press advance the mode one position. do this till you find the one that works. There are only four to try

Oct 03, 2012 | Cars & Trucks

1 Answer

Speedo on my fiat brava does not work most of the time, any solutions


try checking if the cable is hooked properly in the back of the speedometer if this dosnt work try buying a new cable for your car

Mar 23, 2010 | Fiat X1/9 Cars & Trucks

1 Answer

Battery hooked up backwards


need to have it tested to see if there is a diode in that system they pluginto the fuse panel under thee hood like a fuse but it says diode on top? also have wiring tested at alt make sure you have 12.6 volts at big wire on alt? hope this helps

Aug 27, 2009 | 2007 Lexus GX470

2 Answers

Bad starting


what do you mean "bad starting"

starter dosnt engage?(starter engauges but dosnt catch flexplate or flywheel, maybe dosnt engauge at all)
barely turns over? (like theres no battery causing hard crank)

you can test your battery by starting the car with the headlights on, if the headlights go dim the battery is bad. your battery could be out of date or the alternator could be bad and not charging the battery.

Nov 13, 2008 | Mazda RX-8 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...