Question about Ford F-150

Open Question

Need latch cable for F150 - 1999 pickup. Need just the cables. Have a 4 door truck

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chrischronic
  • 235 Answers

SOURCE: 99 f150 hood latch will not release cable rusted or stuck

pull the latch like you normally would, then look under latch to see the cable. get a pair of vise grip pliars and lock on to this cable and pull hard.

Posted on Feb 19, 2009

  • 4369 Answers

SOURCE: 1999 Ford F150 supercab - back driver door won't open

Latch —Rear Door, Lower Removal

  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the rear door radio speaker (18808).
    1. Remove the screws.
    1. Disconnect the electrical connector.
    1. Remove the rear door radio speaker.
  1. Carefully peel off the rear door watershield.
  1. Position the lower rear door latch outside of the door.
    1. Remove the screws.
    1. Position the lower rear door latch outside of the door.
  1. Remove the lower rear door latch.
    • Disconnect the cable.
df9f370.gif
6fbdcc7.gif

Posted on Feb 26, 2009

  • 98 Answers

SOURCE: hood latch 93 sentra, cable is slack like it broken

the hood latch is stuck.U can try tapping on the hood by the latch while slowly pulling up on the hood.Or u can climb under the car and push the lock lever back and that will pop the hood

Posted on Mar 08, 2009

  • 1 Answer

SOURCE: No hood release cable Chevy S10 truck

I have this same problem. You have to take a screw-driver (philips) and look between the hood and the grill and you will see the hood latch assembly. There will be a large gauge wire with a loop about the size of a large philips head screw-driver. This is the release. Take the screw-driver and push the wire towards the drivers side door and it will release.

Posted on Sep 04, 2009

Testimonial: "THanks, solution concise and tells me where to look and how to do it. Because I was looking to taking off my grill and not sure how to do that."

tjspear
  • 66 Answers

SOURCE: Broken latch cable on 2000 Tundra, will not open

remove the door panel, i believe the handle uses a cable on the link... simple fix

Posted on Sep 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Open a crew cab stuck door on F-150 pickup truck


check the opposite side door to see if you can take off the inside door panel with the door closed. If you can, remove the door panel and find the cable/mechanism to the latch, move it to open the door and fix/replace.

Sep 27, 2014 | Cars & Trucks

1 Answer

2000 ford f 150 supercab back door on drivers side will not open


The cable runs from the latch to the handle, it sounds like the cable broke off one end or fell off,

this truck uses cables instead of metal rods to open the latch, remove the door panel and see if the cable fell off handle area or latch,,
the cable operates the inside door handle and sometimes the outside handle but very rare that it operates the out side handle to open door.

Nov 09, 2012 | Ford F150 Cars & Trucks

1 Answer

Install door latch cable


Technical Instructions
See picture below
1. Remove door trim panel and water shield per
NOTE: Place a strip of masking tape along the edge of door before removing trim panel to prevent scratching the door with the trim panel removal tool.

2. Snap cable housing end from slot on inside door handle assembly and disconnect cable.
NOTE: Use care to prevent bending of cable housing retainer bracket.

3. Remove rear window channel retaining bolt to allow access to door latch.

4. Position a block (screwdriver handle) between the latch and the door inner panel and snap the cable housing end out of slot (towards inner panel) on door latch assembly and disconnect cable at latch.
NOTE: Use care when removing cable housing to avoid bending of the latch. Discard cable.

5. Hook up new cable at latch and snap cable housing end into slot.
NOTE: Make sure the cable housing is fully seated in the slot.

6. Apply a light film of Teflon grease to the barrel end of the cable. See Figure A.

7. Install return spring. See Figure A.
NOTE: Ensure that the push button rod is located between the spring and the door inner panel.

8. Install foam block at latch. See Figure A.

9. Position water shield over the return spring and install push pin to retain upper portion of water shield. See Figure B.
NOTE: Push pin goes in the same hole as the return spring.

10. Clean hands of grease before performing step 11.

11. Remove protective backing along the lower edges only of the water shield. See Figure A.

12. Install latch water shield at door latch. Pinch the exposed adhesive surfaces together to secure the water shield. Check to insure water shield is not showing through the door shut-face latch access hole. See Figure B.

13. Attach cable to inside door handle assembly and snap cable housing into slot.
NOTE: Make sure the cable housing is fully seated.

14. Check the gap as shown in remote control using a 3/16 drill bit shank end. The drill bit shank should fit in the gap without any clearance and a tight fit is preferred. See Figure C.

15. If the drill bit is too loose or does not fit, adjust by bending the cable bracket as required.

16. Place plastic wedge on remote bracket as shown. Wedge must fit with at least a light press fit for retention. See Figure D.

17. After installation, Apply a dab of special Teflon grease, supplied with the service cable to cable housing openings at inside handle end. The grease should surround and contact the cable all the way around, to seal the opening between the cable and the cable housing.

18. Check all latch functions to insure correct assembly of latch system. If the inside handle does not release properly, replace the inside handle remote release mechanism.

19. Reposition and install trim panel using new push pins if required.


emissionwiz_53.jpg

Dec 07, 2010 | 1993 Ford F250

2 Answers

Trunk latch on 2002 Civic EX 4-Door won't close


trunk latch cable probably needs to be replaced

Jul 06, 2009 | 2002 Honda Civic

2 Answers

1997 F150 Pickup door wont open


I believe there is a cable which connects the handle to the latch, they are pron to breaking.

Jun 21, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Broken door handle - 2001 Nissan Quest SE


first you van order parts at discount from tascafordparts.com.
quest & mecrury villager are the same vehicle made at the same assembly plant. good luck to all. If you were in detroit area, I wold help you.

Trim Panel —Sliding Door Removal
  1. Remove the sliding door trim panel finish panel.
532ac84.gif 2. Remove the sliding door trim panel 2965fbe.gif Latch Remote Control —Sliding Door Removal
  1. Remove the rear sliding door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. If equipped, disconnect the sliding door power door lock actuator electrical connector.
f373e91.gif
  1. NOTE: Mark the position of the sliding door rear latch cable adjusting bracket before removing the bolt.
  2. Disconnect the sliding door rear latch cable.
  3. Remove the bolt.
  4. Remove the sliding door rear latch cable adjusting bracket from the latch remote control.
  5. Disconnect the sliding door rear latch cable from the latch remote control.
b8f2f32.gif
  1. Remove the 4 sliding door front latch bolts.
NOTE: If necessary, transfer parts to the new sliding door latch remote control.
Remove the sliding door latch remote control.
  1. Remove the bolts.
  1. Remove the sliding door latch remote control.
cb5ee71.gif
Handle —Exterior, Sliding Door Removal
  1. Remove the sliding door latch remote control. For additional information, refer to Latch Remote Control—Sliding Door .
  1. Remove the sliding door exterior handle.
    1. Remove the nuts.
    1. Remove the sliding door exterior handle.
0c820f3.gif

Mar 08, 2009 | 2001 Nissan Quest

1 Answer

Hood latch 93 sentra, cable is slack like it broken


Cables get stretched over time. Should be an easy fix just visit your local salvage yard.

Mar 07, 2009 | 1993 Nissan Sentra 4 Door

2 Answers

Electric window cable solution


My drivers side quit working. I took the door/window assembly apart and found that a small plastic clip had worn/broken. I modified it to hold the cable securely. The problem I had was knowing how the cables routed in the door and window assembly to put it back together. I found an online picture of a new one and routed my cables per the photo. It has not given me problems since. Time invested, about 3 hours. Cost was $0. If you buy a new one, cost is about $80 (online) and time would be about 2 hours. If you have the $$, buy a new one.

Oct 04, 2008 | 2002 Dodge Dakota Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...