Question about 1988 Jeep Wrangler

1 Answer

I have a carter carb 2731,i cant find a rebuild kit.any suggestions?or a different carb needed?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

Try JC Whitney.com

Posted on Mar 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I would like to know if you have a carter carburator diagram for a 2bbl carb


Www.carter.com ask for exploded views of your carb you'll need the tag number on the carb. Its relatively easy to do as long as your float level is correct or google carter carberators using the tag number

Feb 06, 2015 | Cars & Trucks

1 Answer

How To Instruction Manual


It is on the instruction sheet that comes with the carb kit

Sep 20, 2014 | Cars & Trucks

1 Answer

I have a 1973 amc javelin 304 that's hard to warm up when i start it up in the morning and wont idle. once it warm up it miss a little bit what should i do to fix this problem. Thank's


You could try a can of carb cleaner and run it through, it sounds like maybe your choke isn't working quite right. Make sure you give the linkage a good soaking as well and then sprat it with a lube like WD-40 to keep it working freely.
A tune up would help too, plugs and wires for sure. Take a close look inside the distributor cap.Pitting on the contacts or the rotor means they should be replaced as well. The same with the points and condenser. Pitted or burnt points need to come put.When replacing them, set the gap and turn the engine over and re-check the gap. They often need to be reset, especially in older engines that have a little play in them.
You may also need to consider rebuilding the carb. Although there are DIY kits available you may want to consider taking it to a good shop. If you tackle it yourself pay very close attention the how it comes apart, especially the choke linkage. It will go together more than one way but it won't work right if you get it wrong. Also check the throttle linkage for play. If the shafts for the lower butterflies flop around in their holes you will need to get that fixed. There are kits to bush these shafts, but you will need a drill press to get them drilled properly. Play here lets extra air into the carb and makes it hard to get the idle set right because it bypasses the design features to regulate the gas. If you do tackle it yourself there is no such thing as close enough in rebuilding a carb. Your measurements must be exact.
My Chilton book says you could have either a Carter or Motorcraft carb. You will need the carb number to get a rebuild kit. It should be on the side of the carb, usually the driver's side on the float bowl or throttle body. It's possible it may be on a tag attached to it but that is likely long gone by now. It should be a 4 or 5 digit number that will include letters if it's a Motorcraft. Hope this helps.

Apr 16, 2011 | AMC Wagoneer Cars & Trucks

1 Answer

How do you adjust metring on carb for a carter 1 brl in a 1968 fd falcon futura 200 6cyl


GET A CARB KIT AND REBUILT ITONE BARRELS ARE EASY TO DO ALL INSTRUCTION ARE IN KIT AND IT WILL WORK LIKE ITS NEW ABOUT 30 BUCKS GET A CAN OF CARB CLEANER STICK THE RED TUBE IN THE LITTLE PASSAGES MAKE SURE THERE ALL CLEAN

Oct 19, 2010 | Ford Futura Cars & Trucks

1 Answer

Need an exploded veiw of an abf carter carb the numbers are3h4 9635 s1


This carb does not seem like a factory carb. One place to get a parts exploded view is to get a rebuild kit, they have one included.

Oct 01, 2010 | 1978 Chevrolet C1500

2 Answers

I need a diagram to rebuild the carb for my 67 250 inline 6


When you buy a carb. rebuild kit it will come with the diagram chart and spec to rebuild it.

Jun 10, 2010 | Cars & Trucks

1 Answer

Hard starting after warm up


You need to do a partial rebuild of the carb. Pull it off and put at least the needle and seat in it and also I strongly suggest a float.

May 05, 2010 | Pontiac GTO Cars & Trucks

2 Answers

Fuel wont spray inside carburetor


Try tapping the side of the carb.while some one crank's engine, the float could be stuck, if you buy a rebulit kit it will have the diagram with the kit.

Jan 21, 2010 | 1987 Honda Civic

1 Answer

1954 corvette carter yh carbs, floats set @ 3/8 top, 2'' drop, runs good, but gas runs out the ''side draft '' opening when I shut the engine off. #1 is ok, but center and #3 leak , but not the entire...


Bad seal. Rebuild the Carb with a new kit and make sure you have no extra parts. You should be able to get a carb rebuild kit from your local auto parts store.

Oct 06, 2009 | Chevrolet Corvette Cars & Trucks

2 Answers

Carb


its better to have it rebuilt......... it might be a float issue do u have black smoke when it first starts????

Oct 19, 2008 | 1981 Ford F 150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...