Question about Dodge Caliber

1 Answer

I have 2008 Dodge Caliber and the engine light came on with codes P0017 Crank Shaft Position Cam Shaft Position Correlation - Bank 1 Sensor B can you tell me what this means as i cannot afford to pay $100.00 for a dealership to run their test just to tell me what is wrong?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 117 Answers

Sounds like your crank sensor or cam sensor is malfunctioning. Their positions are not correlating which means they are not in perfect alignment according to the computer. I don't think the parts are very expensive and probably not that hard to replace. I replaced both on my 99 Ford Explorer, and I don't recall it that difficult. Anyway, hope this helps.

Posted on Mar 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2010 Chevy Equinox,Check engine light P0017, Service Stabilitrak comes on and the car loses power. Tried checking the EGR to ensure not stuck open and have had no improvement.


DTC P0017: Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation Bank 1
Which engine does yours have 3.4 or 2.8 , 3.0 , 3.2 , or 3.6 L Chevy Colorado P0017 Case Study Part 1

Dec 15, 2016 | 2010 Chevrolet Equinox

1 Answer

P0016 and P0017 check engine pop up after i run for 10 to 15 miles?


the common causes for code P0017 are as follows:
  • A faulty cam or crank sensor
  • The cam or crank circuit is open or shorted
  • The timing belt/chain is out of time
  • The cam or crank tone ring is slipped/broken
  • A problem in the VVT system P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor) God Bless! Hope this helps you.

Mar 08, 2016 | Cars & Trucks

1 Answer

Volvo code p0017


Ok, P0017 = Cam/Crank Position Correlation Sensor B Bank 1, so that's your Camshaft Position sensor ; which could be either faulty or set in the incorrect position.

Jul 10, 2014 | 2005 Volvo S60

2 Answers

Pcm?


PCM= Powertrain Control Module. It is the brains of the car, it reads the sensor in put from all sensors including the cam shaft position sensor

May 14, 2014 | 2004 Toyota 4Runner

1 Answer

P0017 WHICH IS SENSOR B-BANK 1 ?


code p0117 refers to crankshaft/camshaft position bank 1 sensor A--correlation. It also refers to control modules, cooling fan---no signal
I seeing this as a twin cam engine of either 4 or 6 cylinders . . Both sensors on the cams are sensor A so by banks I take it that it is the LH cam (from front of engine) bank 1 and RH cam is bank 2
correlation means that both cams have to read at the same time to indicate a cam has not broken

Apr 26, 2014 | 2002 Volvo S80

1 Answer

2002 VOLVO S80 T6 CODE P0017


the word correlation means relationship between two or more items . In this case it means that when the crank shaft sensor is triggered then the camshaft sensor has to be in agreement that the position of the piston and valves is in the right position to allow spark and fuel.. there are air gaps between each sensor and the rotor that triggers them and if this is not correct or there is dirt in the air gap ( the sensors may be a bit advanced or retarded in the fitment holes) then this relationship of positions is being interfered with and so you get the fault code. If after rechecking the fitment of the sensors and using a scanner to put the engine light off ,you still have a problem ,I would suggest that you find an accredited shop the does a lot of work on your make of car to assist with the fault.

Apr 23, 2014 | 2002 Volvo S80

1 Answer

I have a 2007 jeep patriot. It stalled at stop sign started ran rough. Parked came back drove it home ran u- scan code p0017 replaced crank and cam sensors still runs rough changed plugs were bad. I was...


code p0017 refers to crank/ cam oosition sensor bank 1 sensor B -correlation ===causes --wiring--CKP sensor--CMP sensor--mechanical fault.
It also refers to control modules, cooling fan--no signal===causes -- wiring--ECM.
If it has a timing chain then the the advice that it will not be the chain is good. So I suggest checking out the cam/ crank sensors and wiring

Oct 22, 2013 | 2008 Jeep Patriot

1 Answer

Camshaft position sensor correlation bank 1 code


timing belt is off by a tooth or two. you probably didn\'t have to replace the coolant sensor; that code sets whenever the sensor is disconnected and the ignition is turned on; and it needs to be reset by disconnecting the battery or with a code reader. anyway, the crank/ cam sensors are out of sync. if you\'ve got the twin cam engine, they are a royal pain to get the belt to lay properly on the two cams.

Apr 15, 2013 | 2007 Chrysler PT Cruiser Touring Hatchback

1 Answer

P0017


The generic code is for the correlation between the crank sensor and the cam sensor on bank one sensor 2 or B.
The computer is not finding the cam in the right position based on the crank sensor and the other cam sensors.
Code 17 for Chevrolet may be different.

Jul 18, 2012 | Chevrolet Cars & Trucks

2 Answers

Jaguar xj 40 sovereign 1994 error code 17


I'm not a Jag expert, but error code 17 is:
P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)
Additional infomation on and cause and possible solutions are here:
http://www.obd-codes.com/p0016
Basically, it looks like you have timing issue. Could be the cam or crank sensor or the timing belt.
The P0017 code would imply that you have at least two cam sensors (V6 or V8). The computer thinks that the B sensor cam is out of time with the other cam and the crankshaft. Depending on the cost and location, you might try changing the cam sensor first. The cost to check or replace the timing belt is probably going to be painful.

Jun 12, 2010 | 1994 Jaguar XJ6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

888 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...