Question about 1990 Plymouth Acclaim

1 Answer

Cant likes cross firing skipping when start and the whole tie, plugs wires cap and rotar button replaced

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,386 Answers

Hi and welcome to FixYa!

It can be a faulty ignition coil. If the coil is faulty the car's current flow tends to skip. Please do replace the ignition coil as a first course of action.

Hope this helps and thank you for using FixYa! Have a good one!

Posted on Mar 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 plymouth grand voyager not fireing at coil also fuel pump not working drove home now won't start lady lost husband with 3 kids 1 grand kid needs help


No spark at the coil replace all spark plug wire and coil wire but start with fuel pump first it wont start anyways without fuel id look into a new cap and rotar with the plug wires might get lucky and find a distributor at a wreckers for the same price as cap and rotar

Jun 10, 2014 | 1997 Chevrolet Blazer

1 Answer

Wont start acts like no fire


If it was running before you replaced wires check the firing order

Jan 26, 2014 | 1999 Dodge Durango

1 Answer

I replaced cap rotar and dist. now it cranks over but will not fire and is back firing


the timing is off a bit! heres how I do it. remove the number 1 plug, stick a straw or similar in plug hole. turn engine over by the crank shaft with a wrench. when piston gets to very top of bore, just before it goes down. this is tdc. remove distributor cap and remove distributor reposition the distributor rotor button facing number 1 plug wire inside cap. replace cap and try it! please let me know if this works for you. good-day ! if you can not get to number 1 plug. just turn the crank to tdc marks are on damper pully or crank. is this a 5.7,

Apr 08, 2012 | 1997 GMC Yukon

1 Answer

I have just completed a tune up on my 1998 Ford Expedition 4.6 L V8 and the truck is backfiring and I can nor find the problem. I have the feeling that I crossed a wire and I cant figure out which on. ...


it definitely sounds like that you have a wire ,or wires crossed on the distributor cap, the firing order should be on the intake manifold, the best way to see what the direction of fire is , is to remove the distributor cap, and have someone crank over the engine, to see what direction the rotor is turning, then after cap is put back on, look for the #1 firing position on the cap, this will be # 1 plug wire, then you will have to continue onward following in the direction that the rotor turned, on the cap, following the firing order, 1 plug wire at a time.

Apr 25, 2011 | Ford Expedition Cars & Trucks

1 Answer

How do I replace the distributor, cap and rotor?


first of all get a piece of paper and draw it out. Label each wire where it go's back in the same place as it is. Then unplug all of them. At the base of the cap there is either two small bolts or screws. Take them out pull straight up on it and it will pop off. then the rotar button has two screws. And there should be grease that comes with rotar button. Make sure follow directions for that. Take em off replace it and cap. Then plug the wires back up. It all only go's one way except the wires.

May 07, 2010 | 2002 Chevrolet Blazer

1 Answer

The car won't start. It tries to but just won't start. There is gas in the cylnders and I replaced distributer cap and rotar button and wires. If I unplug the distributer wires it just turns over. With...


yes,,,unpluging the distributer wires can stop it running,,,,have you put the right plug lead on the right plug???? the fireing order is 1,,3,,4,,2,,,is the points gap set right? try setting them to 18th/inch is the condensor working right?? there are so many parts that can go wrong but if its spluttering your nearly there

Jan 17, 2010 | 1990 Toyota Corolla

1 Answer

My 1995 jeep rangler want start but it turns over i replace rotar button, plugs, wires, distributor cap it's not getting any fire to the distributor cap


Check coil, crank postion sensor and pickup coil inside the distributor. (most likely the cps or the coil)

Sep 27, 2009 | 1995 Jeep Wrangler

2 Answers

Engine has a miss or quiver just replaced plugs,wires,cap,and rotar button


try a different cap. try an ac delco part. common for after market one to do this miss problem. best of luck.

Aug 07, 2009 | 1999 GMC Suburban

1 Answer

Miss fire


If you are getting a multiple miss fire error code then more than likly its a bad head gasket i had the same problem on my 2001 altima

Feb 24, 2009 | 1997 Nissan.5 Altima

Not finding what you are looking for?
1990 Plymouth Acclaim Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...