Question about 1991 Oldsmobile Ninety Eight Regency

1 Answer

Front vibration when braking. replaced both calipers & pads. Any thoughts?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,403 Answers

Usually a front vibration during braking is a warped brake rotor. if it only vibrates from the front wheels during braking, it's bad brake rotors. brake rotors cost $23.00 each at auto zone auto parts stores. just confirmed that for you. thank you for choosing fixya.com

Posted on Mar 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 gmc envoy front pads won't release put on 2 new calipers,2 brake hoses,2 new rotors&pads.I forgot,put on new Master cylinder.changed calipers twice thought they might be defective.


On a 2005 vehicle-- at most-- you may need
new rotors & pads,that is all

I'm lost at that story

Don't really grasp what your doing
or what you got yourself into

If I ask any questions-- I feel I will insult you,
so weigh in if you want

Dec 03, 2014 | 2005 GMC Envoy

1 Answer

Shakes really bad from 55 to 70 mph


First & Foremost, If Smell Of Hot Brakes, Remove One Or Both Front Tires, Use A Flash Light & Look At Both Brake Pads From The Top Side, Check For Thickness Of Pad. Remove Brake Caliper, 2-13mm Bolts, Top & Bottom, Should Slide Up & Off Of Rotor & Brake Pads, Maybe With A Little Light Prying.After Caliper Is Removed, Remember Those Two Bolts You Removed To Remove Brake Caliper, Those 2 Bolts Attached To Brake Sliders, They Should Slide In & Out Very Smoothly, If They Do Not You Will Have To Replace The Bridge (The Whole Piece Those Sliders Are Attached To, 2 Bolts On The Back Side, Will Come Right Off After Bolts Are Removed. Sometimes You Can Bring Them Back To Life By Cleaning Them Out With Carb Spray Then Compressed Air & Ceramic Silicone Grease (Purple Pack From Advanced Auto Counter) Make Sure Both Pieces Are Clean Before Placing Back Together. If They Are Stuck Inside Bridge Piece I Suggest Replace Caliper Mount Or Bridge. (Some Parts Stores Call It Different Names) When Doing A Brake Job Always Check Your Caliper Release Pins & Make Sure They Slide Easily, If The Caliper Does Not Return That Could Be The Smell Of Overheating Brake Pads & Vibration, Also, Your Caliper Will Not Return & Will Wear Top Or Bottom Side Of Pad Very Badly. Good Luck! Probably A Good Idea While You Have It Up On Jack Stands To Pull Up On Bottom Of Tire & Feel If There Is Any Play Or Movement Up & Down, Should Be No Movement, If There Is Movement Your Lower Or Upper Ball joint Could Be Excessively Worn, Should Be Replaced & Realigned.

Jun 23, 2013 | 2004 Chevrolet TrailBlazer

1 Answer

I'm driving a 2000 Chrysler 300M. Had front brake pads & rotors changed 2 weeks ago. Front end has been noisy since & I suspect sticking calipers , as i was informed they did not get clean


The front calipers are not the problem...did a shop replace the pads and rotors? Or did a friend replace these parts. The Chrysler front pads and rotors are an excellent design...easy to service and replace parts...only 2 bolts hold on each caliper, and the rotor is held in place with the caliper, and wheel. My first thought was a front wheel bearing is grinding, but you should have noticed this before the brake parts change. The pads could be installed backwards also...my second thought was you may have a loose wheel or two...retighten all 5 lug nuts by using the "star" tightening method, you may be surprised that the loose lug nuts are the only problem. Hope this helps.

Jul 12, 2012 | 2000 Chrysler 300M

1 Answer

1989 toyota pickup front disk brake pads replaced, now the front calipers wont clear the new disk brake pads! Any solutions, please?


remove caliper, push disc all way home, put wheel nut on to hold home, retry fitting them the disc may be slightly scued. If no go try diffrent brand of pad I had same prob with a diffrent car last week & diffrent brand pad was 2mm thiner. If can't exchange pads get piece of emery paper on flat surface & sand away top part of pad material in round motions both ways till they fit. :-)

Jul 09, 2012 | Toyota Cars & Trucks

2 Answers

I have a 2001 dodge ram 1500 that Upon breaking begins to vibrate and kinda bounce plus it wants to pull to he right away from the side that vibrates. Any ideas. The vibrating and shaking begins about one...


You need to have the front rotors turned or replaced. Take a set of dial calipers and measure the rotor thickness. compare that to the specs on the rotor and that will let you know if you can turn them. Put new pads on and make sure to lube the slider pins.

Sep 08, 2011 | 2006 Dodge Ram 1500

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

Should the center spindle nut and 2 torgued phillip head screws be removed to replace front brake rotor on 1999 honda accord lx


will try to help. 1st remove the wheel, then remove the 2 caliper bolts that hold the brake caliper on. after removal of brake caliper, [it should just pull off after the 2 bolts are removed] replace the brake pads[be sure to apply anti squeal lube to the outer side of the pads..not the pad itself,the one not contacting the brake rotor] install the pads, the you will need a C clamp to push the brake caliper pistons back into the caliper. i've used this installation easily. use the old pad ,place it against the caliper piston,then apply the C clamp and push the caliper piston back into the brake caliper, then the brake caliper will slide back over the new pads easily, no need to bleed the brakes if you use this solution. replace the brake caliper bolts, then go to next side and repeat the process. after the replacement of the front brake pads,pump the brakes with engine running!!! it's really a simple process. be sure the brake pads are facing the brake rotors with the [pads] facicing the rotors. no metal facing metal. easy! if you have added brake fluid recently, do not be alarmed if you see fluid coming out of the brake master cylinder,when you use the C clamp to collaspe the brake caliper back into the recessed position. [as always when you have to add brake fluid to the brake master cylinder,it only means your brakes are wearing naturally. if you have a vibration in front wheels or steering wheel when braking, you have a brake rotor or both front brake rotors that need replacement with your brakes also. hope this helps and as always, please get a second opinion if you have doubt. an expert will be happy to help. thank you for choosing fixya.com

Dec 22, 2010 | 1999 Honda Accord

1 Answer

Vibration in rear of vehicle when braks are applied


I believe that the rear discs are warped or the tires are out of round when braking. More likely, the discs. --- The following are the instructions for replacing the front and rear pads for the front/back rotors. 1999-01 Grand Cherokee Front
  1. Drain 2?3 of the brake fluid from the front reservoir. Use the bleeder screw at the front outlet port to drain the fluid. If equipped with anti-lock brakes, relieve the system pressure.
  2. Raise and safely support the vehicle.
  3. Remove the wheels.
  4. Insert a small prybar through the caliper opening and pry the caliper (using the outboard brake pad) to bottom the pistons in the caliper bore. NOTE: This will back the brake pads off of the rotor surface to facilitate the removal and installation of the caliper assembly.
  5. Pry the caliper support spring out of the caliper.
  6. Remove both caliper slide pin bushing caps and slide pins.
  7. Lift the caliper from the anchor.
  8. Using a piece of mechanics wire, support the caliper so there is not tension on the brake hose.
  9. Remove the brake pads from the caliper. Fig. 2: Installing the inward brake pad on the front caliper pistons - 1999-01 Grand Cherokee 93026g92.gif
    To install:
  10. Position the brake pads onto the caliper.
  11. Position the caliper into place on the anchor.
  12. Coat the caliper slide pins with silicone grease and torque them to 21-30 ft. lbs. (29-41 Nm). Install the slide pin bushing caps.
  13. Install the caliper support spring in the top of the caliper under the anchor; then, install the other end into the lower caliper hole. NOTE: Hold the spring in the caliper hole with your thumb while prying the spring end out and under the anchor.
  14. Fill the master cylinder with fluid and bleed the brake system.
  15. Before driving the vehicle, pump the brakes several times to seat the pads.
  16. Install the wheels.
Rear
  1. Drain 2?3 of the brake fluid from the front reservoir. Use the bleeder screw at the front outlet port to drain the fluid. If equipped with anti-lock brakes, relieve the system pressure.
  2. Raise and safely support the vehicle.
  3. Remove the wheels.
  4. Insert a small prybar through the caliper opening and pry the caliper (using the outboard brake pad) to bottom the piston in the caliper bore. NOTE: This will back the brake pads off of the rotor surface to facilitate the removal and installation of the caliper assembly.
  5. Pry the caliper support spring out of the caliper.
  6. Remove both caliper slide pin bushing caps and slide pins.
  7. Lift the caliper from the anchor.
  8. Using a piece of mechanics wire, support the caliper so there is not tension on the brake hose.
  9. Remove the brake pads from the caliper. Fig. 3: Installing the inward brake pad on the rear caliper piston - 1999-01 Grand Cherokee 93026g95.gif
    To install:
  10. Position the brake pads onto the caliper.
  11. Position the caliper into place on the anchor.
  12. Coat the caliper slide pins with silicone grease and torque them to 21-30 ft. lbs. (29-41 Nm). Install the slide pin bushing caps.
  13. Install the caliper support spring in the top of the caliper under the anchor; then, install the other end into the lower caliper hole. NOTE: Hold the spring in the caliper hole with your thumb while prying the spring end out and under the anchor.
  14. Fill the master cylinder with fluid and bleed the brake system.
  15. Before driving the vehicle, pump the brakes several times to seat the pads.
  16. Install the wheels.

Sep 30, 2010 | 2000 Jeep Grand Cherokee

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...