Question about 1995 Pontiac Grand Prix

1 Answer

Second shift start light on - 1995 Pontiac Grand Prix

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 65 Answers

Hello
2nd gear start was the traction control method for the grand prix in 95 there should be a switch to shut if off on the panel by your knees on the driver side to the left
good luck
chris

Posted on Mar 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When shift indicator light blinks off transmission miss shifts


The light indicates a fault has occurred in the transmission or the electronic control sensors and actuators. You need the dealer to scan the transmission control module (TCM) to see what fault code is stored and then based on that code perform diagnostics and repair the transmission.

Apr 01, 2014 | 2011 Chevrolet Colorado

1 Answer

1993 hyundai sonata has check engine light on and is stuck in limp mode and wont shift out of second gear


the .pcm puts it in limp mode and it will stay in mode until light is turned off. You need to get the trouble code, repair it, erase the codes (with a scanner that retrieves the codes), and then you will be out of limp home mode.

Mar 23, 2014 | 2001 Hyundai Sonata

1 Answer

94 Camry shift solenoid problem


It is the shift solenoid.. the solenoids are like a fuse and they pop easy and go bad all the time

Jul 04, 2013 | Cars & Trucks

1 Answer

2000 Honda Odyssey. The passenger side headlamp burned out and I replaced it, no issues two days ago. Battery was cranking slowly and terminals were corroded so I cleaned them. Last night in 15 degree...


The driver's Multiplex Control System is a small computer that controls (among many other things) the dash lights brightness, ignition key interlock, shift interlock, and has a tie in to the brake light system and horn relay. It may be that this small computer malfunctioned and started the whole problem chain.

However, I note from the factory shop manual that if polarity is reversed on the shift interlock--it can be damaged. Reverse polarity will ruin the diode inside the shift interlock. This could have happened when you jumped the battery--a brief period of getting the cables and terminals mixed up could have done it.

Checking the shift lock solenoid can be done by removing the steering column upper cover. Disconnect the shift lock solenoid connector (2 terminals). Using long jumper wires, apply battery voltage to terminal 1 (yellow wire side) of the solenoid and ground terminal 2 (green wire side). Check that the shift lever can now be moved out of Park. NOTE: applying voltage in the opposite direction of that above will damage the diode in the solenoid and will probably ruin it. Remove your jumpers and shift back to park and check that the solenoid locks. If the solenoid does not work properly, it will need to be replaced. This involves removing the end of the transmission shift cable and is a complex job. Remember, no power to the solenoid equals a locked solenoid--it takes power to unlock it.

The Multiplex Control Unit has a self diagnostic feature which checks the computer itself and inputs to the computer. The computer check is called mode 1 and the input test is mode 2. The diagnostic trouble codes are outputted to the ignition key light and beeper.

To test, first confirm that all fuses are good, especially fuse 9 (10A) in the driver's under dash fuse box (left kick panel) and fuse 13 (7.5A) in the passenger's under dash fuse box (right kick panel). Then use a jumper wire (a wire with small alligator clips on each end works best) to jump the two leads of the multiplex test connector. (This is a light green 2 terminal connector dangling from the same wire bundle as the brake pedal switch connector.) Buckle the driver's seat belt (avoids nuisance beeps). Now turn the ignition switch to on. After about 5 seconds, the ignition key light should come on and the beeper should beep for 2 seconds then stop for .2 sec. then beep once for .2 seconds. This indicates that the system is in diagnostic mode 1.

If no diagnostic trouble codes (DTC's) are present, the key light and beeper will not blink/beep again. If there are codes: about one second after entering mode 1, the key light and beeper will indicate the DTC and repeat it every 3 seconds. If there are more than one, the system will indicate them in ascending order. The codes will be a light flash and beep so you will have to count the flashes/beeps to keep track. The codes range from 1 to 6. Code 3 (three flashes/beeps) indicates a problem with the multiplex control unit itself. Write back here for other codes or for questions about mode 2.

Jan 23, 2011 | 2000 Honda Odyssey

2 Answers

Can a 1998 4x4 S-10 blazer be dinghy towed?


Yes it can, just place your Transfer Case in Neutral position.
Shifting into NEUTRAL
To shift the transfer case to NEUTRAL do the following:

Make sure the vehicle is parked so that it will not roll.
Set the parking brake.
Start the vehicle or turn the ignition to RUN.
Connect the vehicle to the towing vehicle.
Put the transmission in NEUTRAL (N).
Shift the transfer case to 2HI.
Simultaneously press and hold the 2HI and 4LO buttons for 10 seconds. The red NEUTRAL light will come on when the transfer case shift to NEUTRAL is complete.
Shift the transmission to REVERSE (R) for one second, then shift the transmission to DRIVE (D) for one second, or FIRST (1) for vehicles equipped with a manual transmission.
Turn the ignition to LOCK.
Place the transmission shift lever in PARK (P), or FIRST (1) for vehicles with a manual transmission.
Release the parking brake prior to towing.

Shifting Out of NEUTRAL
To shift out of NEUTRAL:

Set the parking brake and apply the regular brake pedal.
Shift the transmission to NEUTRAL (N) and turn the ignition to RUN with the engine off.
Press the button for the desired transfer case shift position (2HI, 4HI, AUTO 4WD or 4LO).
After the transfer case has shifted out of NEUTRAL the red light will go out.
Release the parking brake.
You may start the engine and shift the transmission to the desired position.
Excessively shifting the transfer case into or out of the different modes may cause the transfer case to enter the shift protection mode. This will protect the transfer case from possible damage and will only allow the transfer case to respond to one shift per 10 seconds. The transfer case may stay in this mode for up to three minutes.

NEUTRAL: Shift the vehicle's transfer case to NEUTRAL only when towing your vehicle.
Good luck and hope this answers your question.

Jan 30, 2010 | 1998 Chevrolet Blazer

3 Answers

I CAN NOT SHIFT THR TRANS INTO NUTRAL SO I CAN TOW IT BEHIND MY MOTOR HOME. IT WILL SHIFT INTO 2H, 4H, 4L


Shifting to NEUTRAL
To shift the transfer case to NEUTRAL, first make sure
the vehicle is parked so that it will not roll:
1. Set the parking brake.
2. Start the vehicle.
3. Connect the vehicle to the towing vehicle.
4. Put the transmission in NEUTRAL (N) or have
the clutch pedal pressed for vehicles with
manual transmission.
5. Shift the transfer case to 2HI.
6. Simultaneously press and hold the 2HI and
4LO buttons for 10 seconds. The red NEUTRAL
light will come on when the transfer case shift to
NEUTRAL is complete.
7. Shift the transmission to REVERSE (R) for one
second, then shift the transmission to DRIVE (D)
for one second or FIRST (1) for vehicles with
manual transmission.
8. Turn the ignition to OFF.
9. Place the transmission shift lever in PARK (P) or
FIRST (1) for vehicles with manual transmission.
10. Release the parking brake prior to towing.

************************

Shifting Out of NEUTRAL
To shift out of NEUTRAL:
1. Set the parking brake and apply the regular
brake pedal.
2. Start the vehicle with the transmission in PARK (P)
or FIRST (1) for vehicles with manual transmission.
3. Press the button for the desired transfer case position
(2HI, 4HI, AUTO 4WD or 4LO).
4. Put the transmission in NEUTRAL (N) or press the
clutch pedal for vehicles with manual transmission.
5. Shift the transmission lever to the desired position.
After the transfer case has shifted out of NEUTRAL,
the red light will go out.
6. A re-engagement sound is normal when shifting out
of NEUTRAL.

Jan 22, 2010 | 2000 GMC Jimmy

1 Answer

1998 F150 Reg Cab 4x4 won't shift to 3rd.


If there is a problem with the 3-4 solenoid then a check engine light would be on or the OD light would be flashing. Read the faultcodes and see what is there.

Jun 20, 2017 | 1998 Ford F150 Regular Cab

1 Answer

1996 Olds Aurora no shift stuck in second gear


its the shift solenoid theres 2 of them ones about 100 bucks the other was 45 mine had the same problems i paid a guy 100 bucks to drop the pan and change the switch shifts like new happened at about 128000 miles

Feb 14, 2009 | 1996 Oldsmobile Aurora

Not finding what you are looking for?
1995 Pontiac Grand Prix Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...