Question about 2004 Ford F150

2 Answers

Truck stalls replaced fuel filter,alternator,fuel pump,cam shaft sensors and vct selonoid on a 2004 ford f-150 supercrew. any suggestions?

Posted by on

  • 4 more comments 
  • figs4 Sep 09, 2008

    Truck was missing a bit when running down the interstate. Put in some Lucas Oil Fuel injector cleaner, and seemed better. However, it stalled on me after I started it when coming to first stop. It started right back up and I drove it home with no problems. Had the fuel pump sensor changed approx 1 summer ago. Could this be a clogged fuel filter?

  • Anonymous Mar 17, 2014

    what is a cam over connector on the emtc module 2004 ford f-150

  • Anonymous Mar 17, 2014

    light will not go out. have replaced cam sensor and synchronized

  • Anonymous Mar 17, 2014

    Fuel Pump and Filter replaced, Alternator, Starter Relay replaced... Still stalls and takes up to an hour to restart.

  • Anonymous Mar 29, 2014

    Wont start back after shutting down

  • Anonymous Mar 30, 2014

    truck died and wont restart

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 625 Answers

Have you replace the crank sensor? or cranshaft sensor?
if not do it, but before you do that make sure to have the truck inspect for a posible aftermarket alarm installed if it does have it remove and drive it for a few days,
and please after trying leave ranking or feedback for me, thanx and good luck

Posted on Aug 23, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

What are the trouble codes? Recently had 0171 and 0174 codes. Engine coughed (or sneezed) upon a start one morning producing this problem resulting in very rough idle and stalling within 2 min of idling. Problem was vacuum hose blown off fuel regulator which is near impossible to reach without removing intake maniforld since the regulator is located between engine and firewall on 5.4l.

Jim

Posted on Sep 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 ford f150 5.4 3v idles rough but clears when rev engine up


Does you f 150 have electronic throttle control ? An does it have Variable Cam Timing (VCT) - if it does have Variable Cam Timing (VCT) it doesn't have an EGR valve ! What type scan tool did you use to pull the code with ? My FORD factory service information does not show that code for A 2004 F - 150 5.4 L 3 valve engine !

Aug 29, 2015 | Ford Cars & Trucks

1 Answer

I have a ford falcon 2002 xr6 ute with vct tickford motorist just stoped while driving gave a miss fire I have replaced crank sensor module coil fuel pump fuel filter still wont run running very ruf


On my falcon the same thing happened changed dizzy, coil even got new spark plugs what it turned out to be was auxiliary shaft that turns the dizzy or the dizzy module if you got coil packs. You can't see down the dizzy hole because its under the inlet manifold so take photo with your phone and you might see little bits of metal The auxiliary shaft teeth on the dizzy end where worn out and folding over so it can't give the proper spark at right time so went to wreckers 20 bucks for another. ford says it can't happen but I know quite a few engines with same problem

Dec 13, 2014 | Ford Cars & Trucks

1 Answer

I have a 2004 f-150. 1,2,3 and 4 cylinders are not hitting. A couple of days ago it was 1,2 and 6 not hitting. Have put it on 3 different computers and all give me different codes. Any suggestions would...


replace your VCT sencor (variable cam timing) on right bank easy to get to very front of valve cover on top with wire conector un plug pull rubber boot and ther is only 1 8mm bolt loosen it and pull VCT from valve cover and replace just as pulled

May 13, 2012 | 2004 Ford F150

1 Answer

Engine misfire first 1000 rpm, engine flooding out, check engine light is on but flashes when in motion, scanner shows system too lean bank 1 and 2. shows multiple cylinder fault codes.. (FORD F-150...


my 2002 ford f150 4.2 would not hold idle so we changed the fuel pump and fuel filter and relay now the truck starts holds idle runs good at low rpm but when i stomp it it runs then stalls and picks up again.

Dec 05, 2010 | 2002 Ford F150 Regular Cab

1 Answer

Truck stalled out while driving will not start


Not sure about your truck older Fords have 2 fuel pumps 1 in the tank & 1 under cab drivers side. Anytime you change a pump you must change your filter. also check your fuel line if it has been pinched or has a leak pressure will drop

Jul 14, 2010 | 2004 Ford F150

3 Answers

My son's 2004 Kia Optima started stalling on the highway. 1st he noticed the RPMs drop then come back up. This happened several times before the car finally stalled. After a couple attempts, it...


Start with the simple and replace the fuel filter. The fuel filter should be replaced every 15,000 miles or once a year to ensure the fuel system is running 100%. Auto Zone will have the fuel filter and can give you the step by step instructions to getting the job done with common tools. If it's the fuel pump failure, you have not gotten the car restarted. Good luck and keep me posted, be glad to know you got your car running 100% again soon and please rate.

Jan 11, 2010 | 2004 Kia Optima

1 Answer

Motor stalls when driving then starts and stalls right away.


Replace the distributor's magnetic pickup located inside the distributor surrounding the distributor shaft, the only other thing thankfully on this ignition system if memory serves me on the f 150 straight six 300 cu inch is the dura spark ignition control box, of course do the obvious tune up parts replacement dist.cap rotor,plug , sparkplugs before spending the $40.00 - $50.00 bucks on the dist.. pick up, you may have a weak a fuel pump check for adequate fuel pressure at carb 7 - 10 lbs.

Aug 06, 2009 | Ford F-150 Cars & Trucks

1 Answer

Will not start


Have you changed the fuel filter; checked the fuel pump?

Oct 04, 2008 | 2004 Ford Focus

2 Answers

Ford f-150 lariat super crew


hey very frustrating i know mine does the same it looks to me that the problem is revolving around the throttle body or the tps throttle positioning sensor i was looking at all the postings on here sounds legit

Sep 22, 2008 | 2004 Ford F150

Not finding what you are looking for?
2004 Ford F150 Logo

519 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...