Question about 2001 Hyundai Elantra

1 Answer

How to replace a manifold I have been told the manifold has a crack in it, and I would like to replace it myself. also a whirling noise from steering when turnig to the right?? could this ne diff and needs oil?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 5,370 Answers

Yes it can be low steering fluid causing the steering noise,but if the fluid is full then it can be faulty pump causing this. If you have to rev up the engine to move the wheels, suspect the pump is not good. If you have to add oil because it was low, the pump could already have been damaged by low oil.If your noise is with the car standing still, the sound is probably from the pump. ----------- First remove air filter snorkel assembly , unhook purge shut off valve on back of intake manifold ;just remove one bolt and let sensor hang there out of the way.Remove 8 bolts holding manifold to block , if you want to block off the glycol flow to the manifold like some people do for more performance; perfect time to loop intake and return hoses that make changing the gasket a bit more awkward when still attached. Put a light coating of grease on both sides of gasket before installing .---------- Leave the fuel lines hooked up to the fuel rail.its really not that bad...as long as you have the tools. You will need need some long extensions to get at the lower middle nuts. You can also just leave the fuel lines along and remove the two 12mm bolts that hold the entire rail on and pop the injectors out (just be careful not to damage the o-rings and spray they with silicone before they go back in ). ------------ This should help.Thanks.Helpmech.

Posted on Mar 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can a cam shaft synchronizer make a rattling noise ?They usually make a chirping noise when they go bad. I was told by a Ford tech that it was the synchronizer making the noise. This is a 01 Windstar.


they make all sort of noises not just chirp they can make grinding,clanking,whirling ,clunking etc really no set noise because if broken verses worn will give different noise

Aug 14, 2016 | Ford Cars & Trucks

1 Answer

2006 Nissan Murano has exhaust noise coming from rear manifold vicinity. No visible cracks or corrosion


The cracked in the right side manifold is visible when you look up from the upper oil pan area to the underside manifold, the crack is small in the front runner. it takes 2 to 3 hours to replace it thru wheel well area.

Oct 08, 2013 | 2005 Nissan Murano

1 Answer

1987 Ford f350 lariat idles louder than usual and makes ticking sound that it used to not do. Been told few times it's an exhaust leak... Not sure. Any suggestions? And how expensive is it to get an...


There is a tick noise that comes from a failed exhaust gasket or cracked manifold. You will have to remove the manifold to replace the gasket. To go to all that trouble I would have the manifold machined to ensure that it is straight as they have a tendency to warp from the heat and from incorrect tensioning sequence of the manifold bolts/studs

Sep 28, 2013 | Cars & Trucks

1 Answer

3.8 crack in exhaust manifold whats involved in changeing it


the 3.8 ltr engine is a v6 configuration , so there are two exhaust manifolds... one at the rear (firewall side) and one in front.

the front one is easier to replace of course.

Mar 25, 2013 | 2000 Dodge Grand Caravan

1 Answer

Noise coming from near the engine, friends have told me it may be a cracked exhaust manifold.


Yes, that is possible. Or exhaust manifold gasket. I would need more details on area of noise, and do you see or smell exhaust from that areas? Let me know , glad to help you, thanks Mike

Jun 06, 2011 | Toyota Camry Cars & Trucks

1 Answer

Saab 1885 900 se has whirling noise when trying to


If the noise is just a spinning sound and not a grinding, than you're starter solinoid is probably bad.
You're best bet is to replace the starter. Hope this helps.

Mar 13, 2010 | 1995 Saab 900

1 Answer

2005 XC90 T6 AWD making a whirling noise upon acceleration


Add me to the list. Just got back from a Volvo dealership in Chicago and was told the 'winding' noise we're experiencing during deceleration in our 2004 XC90 is due to a failing transmission,so i would suspect the same accelerating. hope all works out for you

Jul 14, 2009 | 2005 Volvo XC90

1 Answer

96' toyota corolla Exhaust Manifold Keeps Cracking


Sounds weird that this problem keep occurring over and over. Does it crack in the same spot every time?

Only two things I can think of that would cause this problem.
1. Extensive over heating, I've seen a exhaust manifold get glowing red hot because of a bad oxygen sensor.

2. Excessive Vibration. The whole exhaust line to the back of the car is moving around too much or too stiff. The exhaust line needs to move around enough to take the movement/vibration of the engine. I would check out for bad motor mounts and worn out exhaust pipe mounts.

May 17, 2009 | 1996 Toyota Corolla

1 Answer

Replacing an exaust manifold in a 1989 4Runner


see where the crack is. if it only requires a gasket, 450 is too much.

Oct 22, 2008 | 1989 Toyota 4Runner

Not finding what you are looking for?
2001 Hyundai Elantra Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...