Question about 1991 Pontiac Bonneville

2 Answers

How long should it take to remove and replace the cv axle on a 92 pontiac bonneville

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Depending on who does it and how "professional" they are and of course if anything is siezed or damaged minimum time to remove is approximatley 1 hour.

Posted on Mar 17, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 83 Answers

Labor calls for 1.5 hours.

Posted on Mar 17, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Is there a bearing or bushing on the shaft that the left axle slides onto on a 1999 Bonneville se?

i have been fooled by this one way to many times. when a wheel bearing or hub assesembly is making noise, it will sound like it is comming from the other side. i do not know why this is. but one test will prove if and which one. when growling noise occurs, notice, when turning left or right, does noise get louder and quieter as you turn? if so then it is wheel bearing. when turning left the right side will make more noise. when turning right the left side will make more noise. if always the same then, tires or transmission need addressing. the cv axle does not make a growling noise, unless front wheel drive car does not move, it makes a clicking or poping noise. sorry but at least you dont have to replace other axle

Sep 12, 2014 | 1999 Pontiac Bonneville

1 Answer

09 Ford Escape, Is it possible to replace CV joint without disconnecting the strut mount fom the seering knuckle? I ask because I managed to do it on 92 Pontiac Transport and curious if I can repeat the...

some vehicle s you can and others you cannot . It depends on the length of the axle from the cv joint as to be able to get it out of the stub section.. Sometimes removing the steering rod ball joint may allow extra turn of the wheel to pull it out but I doubt it.. Any workshop manual will tell the story.

Apr 21, 2014 | 2009 Ford Escape

1 Answer

Replacing 2000 pontiac bonneville cv axle

do you have access to a torch-you'll need it-and you'll also need 1/2" drive impact and sockets and a big socket for the axle nut-like a 30,32,or 36mm and a ball joint fork too-tough job -Denny

Dec 31, 2013 | Pontiac Cars & Trucks

1 Answer

2002 Pontiac Bonneville shakes between 50-60mph. only when under power, not coasting

Check motor & transaxle mounts,all of them
Check Axle CV Joints
Check entire front suspension parts for wear,
especially inner tie rods on steering rack

Aug 01, 2013 | 2002 Pontiac Bonneville

1 Answer

How do you remove the drive axle on a 2001 pontiac bonneville

Jack it up so strut has no pressure on it pull the wheel and axle nut and the two bolts from the bottom of the strut arm and pull the spindle and all to the side then pull axle out of the tranny. Hope this helps

Jun 04, 2011 | 2001 Pontiac Bonneville

1 Answer

How do you get the left front cv's and half shaft out of the transmision?

there is a c-clip on the end of the axle that locks into a grove in the axle gear, they can fit pretty tight, some times you have to wrap a cable arond the in-board CV joint and aitches the cable to a slide hammer and give it a good pop, they do make a puller for the this purpose but it does just what i have told you to do. also some times you have to remove the other side axle and use a long screwdriver to go threw the trans-axle and push the axle out. most of the time you can just use a long chisel and put the tip on the lip of the CV joint and hit it with a hammer.

Apr 14, 2011 | 2001 Pontiac Bonneville

2 Answers

Popping sound in front end when turning

more than likely a bad cv joint on the axles check the axle boots if they are cracked replace the axles

Jan 26, 2011 | 1998 Pontiac Bonneville

1 Answer

Fuse panel diagram 92 pontiac bonneville

Remember that you have several locations to Fuse Panel; check in the Pontiac Bonneville - Owners Manual (page 266 and next) for details and descriptions...


Hope helps (remember rated this)

Jun 11, 2010 | 1992 Pontiac Bonneville

1 Answer

How to put on the new ball joints for 99 pontiac bonneville

make sure the cv axle is all the way in and that the cv joints aren't over extended by turning the axle

Jan 24, 2010 | 1989 Pontiac Bonneville

Not finding what you are looking for?
1991 Pontiac Bonneville Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides