Question about 2000 Ford Expedition

1 Answer

Runningboard lights on one side will not come onjust one side will

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

The side tha is not lighting either has a wire disconected or a shorted wire making for a bad connection could be as simple as checking the ground wire connection too.

Posted on Mar 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

ELECTRICAL PROBLEM


take it to a body shop

Nov 27, 2013 | 2000 Dodge Stratus

1 Answer

Runningboards for ml 250 bluetec 2013 model


You cannot fit these with the correct paperwork ,you need the certificate of compliance for the running boards ,then another certificate from the garage fitting them .Then you have to present the vehicle to the local vehicle test centre to have the paperwork changed to show that the vehicle is fitted with running boards and another complete examination of the vehicle .Failure to comply with will result in the police stopping the vehicle and having it impounded then you will have to pay a fortune to get the vehicle back

Aug 12, 2013 | Cars & Trucks

1 Answer

Side light change


Use a plastic spudger to pry the side light out. Then you can open the light-housing and change the bulb. Check if it's working first. Make sure to clean both surfaces before popping the side light back in place.

May 13, 2012 | 2005 Skoda Octavia 1.9

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

1 Answer

How do I get the side light bulb to change it? on a daihatsu YRV


SIDE LIGHTS COME OUT 2 WAYS. IF YOUR SIDE LIGHTS LENS OR COVER HAS SCREWS YOU HAVE TO REMOVE 2 SCREWS THAT HOLDS LENS OR COVER INPLACE TO REMOVE SIDE LIGHT BULB.SOME SIDE LIGHTS YOU HAVE TO REPLACE THE LIGHT BULB FROM INSIDE THE FENDERWELL.

Nov 06, 2009 | 1988 Daihatsu Charade

1 Answer

Had a problem with a right, amber side marker on right side


Usually one of the holes in the marker light where screw goes in, has metal contact where screw meets light, but if not, and they are not push in wire connection type from behind, then just run your white wire up through hole in housing, and bare the end & tighten it up under screw holding light to body. White should be ground, brown should be power.

Jul 02, 2009 | 2004 Dodge Ram 2500

1 Answer

Right side of trailer running lights does not work


Usually one of the holes in the marker light where screw goes in, has metal contact where screw meets light, but if not, and they are not push in wire connection type from behind, then just run your white wire up through hole in housing, and bare the end & tighten it up under screw holding light to body. White should be ground, brown should be power.

Jul 02, 2009 | 2004 Dodge Ram 2500

1 Answer

Replace front side running light in a 2000 Lexus RX300


Unscrew 3 - 4 screws on the front tire fendor cover close to your side marker light. Pull the fender cover out, use your other hand to reach the side marker light. Using twist and pull the light set out. Replace a new light bulb. Replace everything in a reverse order.

Mar 18, 2009 | 2000 Lexus RX 300

2 Answers

Need to know where to find wires & wire colors for puddle lights


you wil be best to tap right into the battery and give them their own fuse and an iluminated flick switch near the drivers position, yes this will mean drilling a fresh hold for the switch but will make it easier if you extend you light show or add a "remote light controler" later, also they can be a huge drain on the main driving lights when tapped into the factory installed ones, causing them to dim out.

Jan 04, 2009 | 2008 Ford Explorer

1 Answer

2008 GMC Sierra Ext. cab runnungboard lights


yes wire the runningboard lights together and then to the interior light post on fuse box or to interior light switch on drivers side door

Nov 08, 2008 | 2008 GMC Sierra 2500HD 2WD

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...