Question about 1990 Jeep Wrangler

1 Answer

Please help ,i have a 1990 jeep wrangler, while removing the fuse i broke the connector that the fuse goes into. what is it called and where can i get one?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Since you did not mention where the fuse was, you really haven't given enough info. But, if the fuse is in a fuse block, either the under dash one or the power distribution center under the hood, probably the easiest way to do that repair without replacing the entire block would be to take it apart so you can access the wiring inside, behind the one you broke, then get an in-line fuse holder. Attach it to the wiring that goes to the broken port and put the appropriate size fuse in it.When putting it back together, be sure not to pinch any wires including the new ones. Locate the fuse holder near the original block so you can get to it.
When buying the holder, note that they come rated for different draw fuses. Get one that is close to the one you will be using but don't use one that is rated lower. Using a 20 amp holder and a 15 amp fuse is fine but the other way around is not.

Posted on Mar 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 jeep wrangler 2 carbureted fuel pump runs about a second ,fuel shoots out pline at back of carburetor, but none will spray inside


must be 4.2L engine the 2.5 is EFI TBI.(French EFI)
the 4.2 has computer controlled carb from H3LL
never ever buy a jeep like this, ever.
if hellbent on this bad car, to fix then buy the service manuals off fleabay.. (id not even hesitate there)

my guess is the carb is bad, what checks matters are.
fuel nozzles dead, is that.
1: fuel pressure at spec. not dribble tests. (no dribble yes, means pump dead) (using a real pressure gauge)
2: float level correct. ? if bowl dry bingo. !
3: jets not clogged, inside carb.
4; carb computer working (Tests stated in SM)
5: dead carb solenoids.

there is no worse car than a ECM controlled carb. horrid system.
ended in 91. as Chrysler took over..from AMC

join a real jeep forum and hear them moan, ?

2 fuses need to be good, F1 and F2, 1amp rated.
in the diode fuse assembly.
or the idle solenoid goes dead.

Mar 13, 2017 | 1990 Jeep Wrangler

1 Answer

Hello i just purchased a 1990 Jeep wrangler and would like to do a tune up myself, i dont have an owners manual to lead me through it.


A tuneup is easy to do, You don,t need a manual, My 3 year old niece could tune up a vehicle with no help,

Nov 28, 2012 | 1990 Jeep Wrangler

1 Answer

1990 jeep wrangler oil gauge and fuel gauge may be grounded out any body have any help for me


may need a harness wiggle test-they jiggl the wiring around to notice a connection issues--hav an electrical specialist doit--not a dealer please--or get a haynes manual for wire maps

Oct 02, 2012 | 1990 Jeep Wrangler

1 Answer

1990 jeep wrangler 2.5l. my son put a radio in and now the jeep wont start with out using a screwdriver on the starter. what did he do? thanks. you have to turn the key and than get under and jump with a...


check the fuses. its possible he could have popped one when hooking up the Hot wire. if not that then the start solenoid could be bad. but i feel the answer lies with the fuses though

Sep 16, 2011 | 1990 Jeep Wrangler

1 Answer

1990 jeep turn signals don't work


Dear,

please look for the fuse for the side indicators.

also look for the turning switch wirring and connections.

look for the bulbs condition too'

thanx

May 16, 2011 | 1991 Jeep Wrangler

1 Answer

Tail light and dash light won't work on my Jeep wrangler 1990 4.2l.


Probably just a fuse. Check your owners manual for fuse box location

Jun 28, 2010 | 1990 Jeep Wrangler

1 Answer

1998 Jeep wrangler


Remove the inner door panel and check to make sure that the linkage rod that goes between the outer handle and the latch is connected. It's possible that the plastic end clip broke.

Jul 10, 2009 | 2006 Jeep Wrangler

1 Answer

Running lights in both back and front do not work.


Yes all automotive lights are connected in series and all bulbs need to be change up one digit, for example if you have a 9004 bulb you must install a 9005 to all lights even if they do not normally take this bulb.

Feb 19, 2009 | 1990 Jeep Wrangler

1 Answer

1990 jeep wrangler


YES BECAUSE YUOR CLUTCH IS HDRDRAULIC, SLACE IS INSIDE BELL HOUSING

Jan 02, 2009 | 1990 Jeep Wrangler

Not finding what you are looking for?
1990 Jeep Wrangler Logo

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...