Question about Dodge Colt

1 Answer

HOW CAN I RESOLVE\REMOVE STUBORN SPLINED END ?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

What is the splined end on please ?

Posted on Mar 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the soda bottle cap, from the drive shaft end of a 2004 Saturn Vue V6 AWD, in order to remove the yoke, when replacing the carrier bearing.


Can you post a picture of this "bottle cap".. I think you are just seeing the splines (they can kinda resemble the rough crimpings' that a bottle cap has...
There should be nothing on top / on the end of the Midship splined stub shaft... You remove the hog-ring, and press the yoke off/over the spline. the spline and end yoke have a "dead spot" - which makes you keep the driveshaft in-phase during reassembly.. the dead spot is 2 splines that have been joined together at the end.. the end yoke will have a spline removed to accommodate this...
PS - soak the end yoke and spline liberally with PB Blaster.. Walk away..the longer the better... Then attempt to remove.. Good Luck!

Dec 01, 2016 | Saturn Cars & Trucks

1 Answer

86 bmw L7 735i having trouble puting left rear axle in


IF there are just splines on the end of the axle and nothing else the trick is to use 2 hands on the axle flange (one on top and one underneath) and using opposing forces ( top back bottom forward ) lift the splined end up until it goes into the side gear in the diff. Then it is a matter of twisting the axle flange so that the splines and the side gear splines slip together

Dec 23, 2013 | Cars & Trucks

1 Answer

I cant remove the metal end and spline inside of my kia sedona


Try to get a pry bar or large screwdriver between the CV housing and the transmission case. A little force may be required, but you have to pop the housing out of the transmission. A c-clip in a groove on the splined shaft is holding the shaft in, and must be popped outward, for the housing and shaft to be removed.

Nov 25, 2013 | 2003 Kia Sedona

1 Answer

How can I remove the dipstick tube?


the bottom of the dipstick tube is just pushed into the block, you might have to use some brake cleaner to loosen it up if its being stuborn

Feb 22, 2013 | 2004 Nissan Sentra 1.8

2 Answers

How do i replace wheel side cv joint boot


YOU CAN GET A BOOT REPAIR KIT OR A ZIP BOOT.DO NOT LIKE ZIP BOOT,DOESNT WORK . BEST TO GET A REMANUFACTURED AXLE AND REPLACE AS A UNIT,DOESNT COST MUCH MORE AND WIL WORK WITH A WARRANTY.TAKE OFF WHEEL,LOOSEN AXLE NUT,TAKE OFF LOWER BALL JOINT,POP AXLE WITH HAMMER TO DRIVE AVLE OUT OF BEARING A LITTLE WAYS THEN PUILL UP ON STRUT ASSEMBLY TO GET AXLE ALL THE WAY OUT OF BEARING/HUB ASSEMBLT. POP OUT AXLE ANT HE SLIDE IN THE NEW UNIT

Dec 30, 2010 | 1994 Hyundai Excel

1 Answer

How do i change 2004 toyota tundra rear end drive shaft


1st, with th E brake on and the wheels chocked. Remove the 4 bolts that connect the shaft to the
rear end flange and pull(or pry if required)away from the rear end. Next pull the shaft back toward the rear off of the front spline. You may have to remove the seal from the from the front of the shaft
at the spline to pull the shaft all the way off. Somtimes the grease on the spline creates a vacum
that makes it tough to remove. When you install the shaft there are marks or notch's on the shaft
and rear end flanges to line up as well as the spline+yoke. But an old rule of thumb is make sure
that the U joints are all in line, so if one shaft is at 12:00 ( I ) the other must be at 12:00 also.
Once the shafts are lined up, line up the marks on the flanges and bolt it up.
Hope this helps.

Dec 01, 2010 | 2004 Toyota Tundra

1 Answer

If the axle is broke or removed does that mean that the difereincal pin broke or damaged or if the gears are damaged


never seen an axle fall out--you may have major damage. If you are lucky, the cv joint may have failed suddenly without damaging the tranny or wheel bearing. What do the shaft ends look like? Does it have splines on both ends? Are the splines clean? If yes, you may be OK--just have a new axle put in.

Aug 22, 2010 | 1993 Plymouth Voyager

1 Answer

Removing the right intermediate axle shaft


i can only guess it is a 3.0l 4v well as far as the axle goes, the rh outer half shaft seperates at the splines on the intermediate shaft.
the intermediate shaft is the solid shaft from the trans to a bearing support bracket and ends after that. it is externally splined.
the rh axleshaft , inner cv joint, is internally splined.
to remove the rh axleshaft, remove the rh wheel and splash shield.
removed the lower balljoint pichbolt and seperate the lower balljoint front the steering knuckle. take the axle nut off and using a large brass drift or hardwood, drive the axle out of the bearing-hub assembly. DO NOT DAMAGE THE THREADS. also use some lubricant on the axle nut dissasembly. after the outer axle end is free, using the same brass drift or other, hit the inner cv joint and drive it off the intermediate shaft. inspect the splines closely because these fail and cause a no-drive condition.
then the mounint bolts for the support bearing and pull the intermedate shaft out, you will loose some fluid.

Jan 27, 2009 | 2003 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...