Question about 1998 Lincoln Mark VIII

1 Answer

Mark 8...part13a565 bailest rear light does not function..please advise?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,915 Answers

You can get a better one than OEM (impossible to get new) if you buy a 'glitch' ballast-

http://www.markviii.org/LOD2/inverter/InverterRAI.html

easy to install, and better built

Posted on Mar 17, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the bulbs in the brake lights? I have a 1995 mark 8.


Rear Turn Signal, Brake and Parking Lights
  1. Open the trunk and remove the luggage compartment trim.
  2. Remove the eight nuts retaining the reflector to lower back of luggage compartment
  3. Remove the rear panel reflector assembly from the vehicle. To install:
  4. Installation is the reversal of the removal procedure. Fig. 8: Pull the trunk trim away from the lamp housing assembly 93146p43.jpg
    Fig. 9: Twist the socket assembly and remove it from the housing 93146p44.jpg

Aug 21, 2010 | 1995 Lincoln Mark VIII

1 Answer

The owners manual says for setting the timing is at 8 degrees,When using the timing light, What mark is 8 degrees?


The engine turns clockwise, the first mark is tdc (top dead centre) and the second mark is preset at 8 degrees so when using a timing light line up the second mark on the pulley with the fixed mark on the timing cover at idle

Aug 10, 2010 | 1996 Nissan Sentra

1 Answer

My peugeot 205 has a grd engine i recently did a complete overhaul but i cant find the timing mark for the crunk shaft and camshaft please advise ernest


crunk shaft mark no marks there is a little hole of 6 mm dimater between the crunk shaft and the gear bos on right hand side facing engine near the ex manifold,for cammes sae thing 8 mm hole about 2 o clock facing pulley

Jun 19, 2010 | 1991 Peugeot 405

1 Answer

Clio 2002 authentique 1.2 8 valve stop light & hand brake light stay on in the dash can anyone help!


hi from uk the stop/handbrake light has two warning functions it will illuminate when hand brake is applied or is left on whilst driving or not fully off position ?? the other function is it is warning you that your brake fluid in the reservoir is low/requires topping up ? if it is low ? this could be due to a fluid leak ?either from pipes or wheel cyl's/calipers ? OR ? just that as your b/pads and shoes wear lower then fluid from reservoir displaces from res to cyl's to compensate for wear so may i suggest you 1st check fluid level+top up if low? then check for leaks as above more important have your brake pads and rear shoes or pads if fitted checked for wear/safety i advise this considering age/milage? of car and if you have no record of being checked/replaced recently? if your brake pads are fitted with low pads wear indicators this will also give warning hope this helps? good luck !

Mar 17, 2010 | 1986 Renault Sport

1 Answer

1994 Lincoln Mark 8. Turn signals


Dash lights go through the light switch, any aftermarket addons? old and new multi switch have no effect? usually if any ground issues is towards rear of vehicle.

May 24, 2017 | 1994 Lincoln Mark VIII

1 Answer

No power to bmw x5 ns brake light


Hi , remove the brake light bulb and look at where the bulb contacts the holder , you may find that you have a hole burned into the holder where the contacts have been arking , if this is the case you will need a replacement kight unit , reagards mark

Jun 27, 2009 | 2004 BMW 5 Series

1 Answer

My 1997 Lincoln Mark 8 will not shift into gear.


it may be a shifter linkage issue. There is an interlock to prevent the car from bouncing out of park into reverse and if the linkage is not correctly adjusted, then it locks up.

Apr 20, 2017 | 1997 Lincoln Mark VIII

1 Answer

Check engine light was checked bank 2 sensor 2


Bank 2 is the passenger side. Sensor two is the one closest to the rear of the vehicle, or "down stream" oxygen sensor. If you are uncertain, then unplug the one you think is the problem, and see if another code comes up. If no other codes come up, then you have the correct one.

Mar 26, 2009 | 1999 Dodge Intrepid

1 Answer

Tail lights Infiniti G35 2003 Not Working at All..Bulb Checked..


my g35 tail lights are not working it keeps blowing my fuse.

Dec 05, 2008 | 2004 Infiniti G35 Sport Coupe

Not finding what you are looking for?
1998 Lincoln Mark VIII Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

fordexpert

Level 3 Expert

5572 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...