Question about Cadillac STS

1 Answer

Can't get at it without taking trunk liner out, also, one fog lamp is out, how do you change that? And the smallest light, one of them is out, HOW, without taking the whole head light assembly out? Please HELP!!

Posted by on

1 Answer

Trunk liner has to be lossened and pulled away
Front lamp assy removed
Crawl under car for fog lamp

Posted on Mar 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for fuse for fog lights on a 2008 dodge charger. we installed a fog light kit. the car is pre-wired for them. we replaced the head light switch with the one from the kit. fog lights arent...


Check your instructions with the fog lamps, I believe you will need to take your car to a dealer to have them activate the fog lamp driver in the Totally Integrated Power Module.

Jan 23, 2011 | 2008 Dodge Charger

1 Answer

How do I change my turn signal rear bulb? What tools will I need?


Welcome to Fixya!

Here's the procedure on how to replace the signal light.

1. Open the trunk
2. If you have a convenience net, remove it.
3. remove the top plastic wingnut that the convenience net hooks to.
4. pull back trunk liner
5. remove the 2 plastic wing nuts found under the trunk liner
6. carefully pull the tail light assembly from the vehicle
7. squeeze the tab on the socket (turn signal lamp in the inboard socket)
8. turn socket counter-clockwise
9. pull out the socket
10. pull lamp straight out
11. push in new bulb
12. reverse steps to reinstall lamp assembly
Note: replacing left and right turn signal bulbs takes about 5 minutes.

Thank you for using Fixya!

Dec 06, 2010 | 2001 Buick Regal

1 Answer

How do you get to the left brake light bulb to change it?


Open trunk,pull trunk interior/liner away from back left corner
Remove three nuts, that hold tail light housing
Remove housing and replace burnt out lamp
They use an extended duty lamp/bulb,you may not find that
I add, that most China Made bulbs, don't last a year. So look for a Wagner, made in Mexico,France etc

Oct 22, 2010 | 2005 Lincoln LS

1 Answer

Remove & replace right turn signal bulb


The procedure is as follows:-- Working from the trunk:
1. locate the 2 retaining knobs (doohickeys that you fasten the trunk cargo net to) for the Hard plastic trunk liner near to and inside of the rear light assembly. Unscrew the knobs.
2. Pulling back the plastic liner, locate the 4 studs (threaded posts). 3 will be located vertically in a line, the fourth, outboard and lower. Using a 10mm wrench(small), remove 3 of the 4 nuts fastening the light assembly to the body. DO NOT remove the lowest nut of the 3 in a vertical line, as this does not fasten the light assembly. DON'T LOSE THE NUTS OR WASHERS.

Working from the rear of the car:
1. Hand pull the light assembly from the car body.
2. Remove bad lamp. Twist lamp socket and pull out of assembly. Pull lamp and replace with #3057.
Reassemble:
1. Test light prior to reassembly.
2. Ensure Gasket material for assembly and studs is intact, this keeps water/dust out and dampens movement (prevents rattling and increases the life of lamp).
3. Use Reverse instruction for reassembly.
-------------- The taillight/backup light/license plate light assembly is separate from the brake light/turn signal light assembly on the Buick LeSabre. No matter what rear bulb you have to replace, you must access the trunk area to do so. Open the trunk of the Buick LeSabre.Locate 7 nuts underneath the trunk lid (3 on each end of the trunk lid and 1 in the middle). Remove each one using a nut driver.Manipulate the trunk lid at chest level and gently pull the rear taillight assembly slightly away from the trunk lid.Locate the burned out bulb sockets and then remove the bulbs. Insert the new bulbs into the socket and test by turning on the lights before reassembling.Replace the tail light assembly by aligning the studs inside the predrilled holes in the trunk lid. Refasten the 7 nuts.Remove the cargo net if applicable to replace the brake and/or turn signal light.Unscrew the plastic wingnut that the cargo net is attached to. Pull back the trunk liner.Remove the 2 plastic wingnuts under the trunk liner.Pull the brake light assembly outward from the back of the LeSabre.Locate the socket of the burned out bulb and then turn counter clockwise 1/4-inch to release it from the assembly.Remove the old bulb from the socket and replace with a new one. Test the light before reassembling. Thanks. Keep updated for any more query. You can rate this solution and show your appreciation.

Aug 07, 2010 | Buick LeSabre Cars & Trucks

1 Answer

How to change rear brake light


From inside the trunk, move the liner aside opposite the tail lamp assemblies. There are three plastic wing nuts holding the assembly in place, which you should be able to remove without tools. Once these wingnuts are off, the tail lamp assembly can be pulled to the rear away from the body. The individual bulbs can be removed with a quarter twist of the connector/socket.

Mar 17, 2010 | 2002 Dodge Intrepid

1 Answer

Need to replace the rear turn signal lamp, but can't find where to access it. How do I remove the light cover to replace lamp?


You'll need to remove the liner for the trunk to get to this lamp, which is mounted in a quarter-twist lamp socket which fits into the lens housing. The pieces of the trunk liner fit together one over the other... so look around for the hold-down nut on the side you need to service, then the liner pieces come out one over the other.

Nov 24, 2009 | 1996 Mercury Mystique

1 Answer

How do change the tail light on a 2007 nissan maxima sedan


I think it is the same as a '04 maxima. Open the trunk, from the inside remove the side trunk liner (by removing the plastic tabs the liner can be pulled back). Once the liner is pulled back you will need to remove two nuts which secure the tail light in place. Once the two nuts are removed you can start pulling the whole tail light assembly out. There are two other tabs that secure the tail light in place which may give you some resistance but the light should come out without too much force once the two nuts are removed.
Once the tail light is out you can change whatever bulbs you need to.

Jun 30, 2009 | 2007 Nissan Maxima 3.5 Sl Sedan

1 Answer

Need to change the stop light for 05 nissan maxima.


Open the trunk, from the inside remove the side trunk liner (by removing the plastic tabs the liner can be pulled back). Once the liner is pulled back you will need to remove two nuts which secure the tail light in place. Once the two nuts are removed you can start pulling the whole tail light assembly out. There are two other tabs that secure the tail light in place which may give you some resistance but the light should come out without too much force once the two nuts are removed.
Once the tail light is out you can change whatever bulbs you need to.

Jan 09, 2009 | 2004 Nissan Maxima

1 Answer

How do you reset the fuel pump circuit on 1996 mustang


Open the trunk, the reset switch is behind the drivers side tail light, or inside the rear fender area, behind the interior trunk liner. There should be a small place to put your finger through the trunk liner to reset it, without taking anything apart.

Dec 21, 2008 | 1997 Ford Mustang Cobra

3 Answers

How to access brake tail light to change


Tail light replacement is not as hard as it seems.
Tools needed:flat head screwdriver and a deep 5/32 socket(a pair of pliers will work).
Step 1: open trunk and pull back truck liner at tail light.There is a small button clip on liner.Use screwdriver to pop up the center of button clip,pull clip out of hole.
Step 2:You will see a black wire attached to the body of car with 2 white clips.Use screwdriver to pop clips off of studs.
Step 3:Remove the nuts from the studs and pull tail light assembly straight back away from car.The outer side of the light just snaps in and out of place.
Step 4:Turn light socket counter clockwise 1/3 turn and pull out.
Step 5:Pull bad bulb straight out and replace.Reverse steps to reassemble.

Oct 24, 2008 | 2007 Nissan Sentra 2.0 SL Sedan

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...