Question about Toyota Pickup

1 Answer

NEED TO REPLACE OLD BALL JOINT WITH NEW ONE PLEASE EXPLAIN PROCEDURE

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 47 Answers

You will need a ball joint seperator tool and a large hammer. With the proper tool this is easy. Seperate the ball joint with the tool and hammer and replace with the new ball joint.

Posted on Mar 17, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the right ball joint on a 2000 Chrysler Town and Country?


If you want to take the easy route use the dorman-control-arm- 520-344. It cost about as twice as much as a ball joint by itself but you will not need any special tools to replace. If you just do the ball joint by itself you will need a ball joint tool to press the old one out and the new one in. Some parts store do offer free tool borrowing programs so its you call

Feb 02, 2015 | Chrysler Cars & Trucks

2 Answers

Creaking groan from front driver side tire


The creaking is coming from either the shock ,ball joint, or a-arm bushings. Have someone with you and one person pushing up and down, the other, safely feeling each component till the vibration can be felt. If it is in fact the ball-joint then as long as it is safe (not loose), then just add grease to it as needed and it should go away.

Jun 08, 2009 | 2000 Ford Ranger SuperCab

1 Answer

How do you remove a ball joint on a 1987 ford f150 pickup


When doing ball joints on a truck that old, I suggest you do them all at the same time. You'll need a special tool called a ball joint fork. You remove the cotter pin on the nut that holds the ball. Then you position the fork tool in between the ball joint and the arm it is attached to and hit it with a hammer until the ball joint separates from the arm. Now unscrew the joint from the adjusting tube and replace the joint. Be careful when screwing the new joint into the adjusting tube. count the number of threads that were inside the tube on the old joint and match that number when installing the new joint. Now push the joint back into the control arm and tighten the nut. Put in a new cotter pin to keep the nut from turning. After you've done all the joints , drive the truck for about 50 miles or so then have a front end alignment so your tires won't wear unevenly or if the truck steers to the right or left when you let loose of the steering wheel while moving.

Oct 15, 2014 | 1987 Ford F 150

1 Answer

How to replace ball joints


the lower ball joint is pressed into the lower control arm. You will need a ball joint press to remove and install the ball joint. The other option is to replace the lower control arm.

Some parts store will have presses for loan. You will have to check around and see if any in your area have these. If you can't find one you could always pull the control arm and bring it to a shop or machine shop and have them swap the ball joint.

Its a pretty simple procedure.

1. remove the wheel
2. remove the pinch bolt that secures the knuckle to the ball joint.
3. separate the lower control arm from the knuckle.
4. remove snap ring from the ball joint (if it has one)
5. use a ball joint press to press out the old ball joint.
6. press in the new ball joint.

if you don't have a press than you can remove the lower control arm by following steps 1-3 above. then remove the bolt from the front bushing. Remove the stamped steel skid pan from the sub frame. Remove the rear lower control arm bushing mounting bolts.

If you have any questions I'll be happy to answer them.

Oct 13, 2011 | 1998 Dodge Caravan

1 Answer

Do Buick lesabre 1993 have rear ball joints, and if soo, how do you tell if it is bad, and how would you go about replacing it.. Thank you


YES. jack the car up and shake the wheel side to side. if the ball joint is bad the wheel will feel loose. to replace , you remove the tire, brakes,and unbolt the strut. then you separate the ball joint from the spindle, then press the old joint out of the control arm and then press the new one in . reassembly in reverse procedure and then have the car aligned.

Aug 14, 2011 | 1993 Buick LeSabre

1 Answer

How do i replace the ball joint on a 1996 chevy blazer four wheel drive


you need to purchase a pickle fork from a local parts store to remove old ball joint then replace new one using a jack to put pressure on it while you tighten new joint in place.

Dec 06, 2010 | Chevrolet Blazer Cars & Trucks

2 Answers

Replace upper ball joint 2003 silverado 1500


The ball joints on both 2wd and 4wd upper are pressed in you need to remove snap ring and using a hammer pop out the old one out this is after you seperate the upper arm from the spindle. To install the new ball joint you should use a ball joint press that you can rent at most autoparts shops

Aug 09, 2009 | 2000 Chevrolet Silverado

1 Answer

How to change upper and lowwer ball joints


the upper ball joints are less complicated , safely jack up trucks front end and support on the proper weight rated jack stands, place jack stands under lower control arm , remove wheel , locate the upper ball joint shaft and caslte nut, remove the cotter pin retainer and disgard for anew cotter pin on assembly., loosen the castle nut but not all the way just yet, some persons like to use a ball joint fork, so if your going back with new joints then by all means use a fork toll to separate the control arm from the ball joint shaft, a couple of solid hits should bust it loose, with the joint loose from its seat go ahead and remove the nut all the way... if yours ball joint is attached to control arm with bolts tehn remove mounting bolts ,R&R old with new joint and reinstall in reverse order of disassembly.

Lower ball joint is more difficult and also more dangerous because of coil spring has stored energy in it's compressed state, you will need a coil spring compression tool, to do this job, it's best on your first time to have supervision from a qualified experienced suspension and steering technician for this reason I will not explain this procedure not knowing your level of expertise...

Aug 07, 2009 | 1991 Ford F150

1 Answer

Lower ball joint removal from a-arm


The entire control arm is supposed to be replaced on those when ball joint fails. Did you manage to buy another ball joint only?

Apr 26, 2009 | 2001 Nissan Altima

1 Answer

Instructions needed--To help me replace my CV joint and my Ball Joints


the ball joints arent hard to do at all all you have to do is take the front tires off and you will see the ball joints as soon as you do this. then there is a nut on the bottom of the ball joint, remove it. then where the ball joint assembly connects to the tie rod mark where the end of the nut is with a sharpie. then loosen the compression nut that holds the ball joint then use a large wrench to loosen the ball joint assembly. then take off the old ball joint and replace it wit the new one lining up the backside of the compression nut with the mark you made with the marker then tighten. then put the bolt on the bottom of the ball joint assembly back in to the hole where you removed it then tighten snugly and put your tire back on and you are finished and then do the same on the other side

Oct 24, 2008 | 1994 Chrysler Concorde

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

257 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...