Question about Mitsubishi Eclipse

Open Question

I have a 95 eclipse, my reverse lights wont illuminate, i replaced the bulbs and they still on illuminate, i checked the fuse and it is good according to my fuse tester........

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: When I shift to Reverse my reverse lights wont work.

Buy a auto repair manual for your respective truck, or go to the Nissan dealer and ask a tech to show you where the actuator switch is located, and replace that switch. That is the only thing left to replace. That should fix it. Also you could use an Ohm meter to check the switch to see if it is bad. Also check for a broken wire when you remove the actuator switch.
Good Luck!

Posted on Dec 16, 2008

Ad
  • 1114 Answers

SOURCE: 94 toyota previa brake lights not illuminating

CHECK THE BRAKE LIGHT SWITCH UNDER THE BRAKE PEDAL

Posted on Jan 08, 2009

  • 1348 Answers

SOURCE: Reverse lights not working

i would get the diagram and take a look from there.
the safety neutral switch gets its power from a source and then lights up the reverse lights amongst other things.
alot of times vehicles are in accidents and wiring gets damaged.
make sure the reverse circuit is properly grounded.

Posted on May 14, 2009

  • 1986 Answers

SOURCE: reverse lights wont work

On the side of your transmission will be a switch with several wires coming out of it. This is your reverse switch that turns on your reverse lights and most likely needs to be replaced

Posted on Oct 01, 2009

  • 566 Answers

SOURCE: 91 Honda accord

hi from uk if everthing you checked is ok ? then fault is probably the brake light switch is either faulty or the plunger that is supposed to move out as the pedal is pressed so putting b/lights on has stuck inside/off position? so if you look up at b/pedal just below the pivot shaft forpedal you will see the switch and it is srewed into the pedal box assy it has a plug of two wires connected ? pull off plug then use a wire paper clip opened up and join the two contacts in plug this makes connection to b/lights on have assistant check lights work when ignition is on? if yes? then remove clip ign off then unscrew the actual switch from its hole when removed? check if plunger is coming all way out or is stuck ? if either of these try wd40 on the plastic plunger and work it in/out when you are happy it works ok ? then b4 you refit just connect the plug and again test with ign on plunger out lights on! plunger in lights off if it works? then unplug and screw switch back in hole to approx last position and connect plug recheck b/lights operate as you press pedal approx 3/4 " b4 lights operate this is trial+error screwing in or out untill you are happy lights give early warning to following cars that you are braking ? however if lights work with clip but not on switch after completing above ? then you will need to renew switch they do sometimes melt contacts and burn inside mostly due to constant holding car with footbrake instead of park brake for long periods also a common reason for brake light bulbs blowing bad driving habit ! so consider this advise please and hope all is clear above ?

Posted on Dec 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 95 jeep loredo . reverse light is not working , I checked the bulbs and fuses and they all good, I also change the neutral switch, still han no reverse light, any suggestion?


The neutral switch is so that you can't start your vehicle in a gear (drive, reverse, ect.) your looking to replace the backup lamp switch. Not sure where its located on your jeep but that sounds like the problem. Happy hunting!

Dec 17, 2011 | 1995 Jeep Grand Cherokee

2 Answers

My back reversing lights wont work but the bulbs and the fuse are all good?


Hello and welcome to FixYa!

If that's the case then it's definitely a reverse switch issue. If the reverse switch is faulty, the reverse light won't work even if the bulbs are fine. It is located underneath the transmission where it triggers when reverse is engaged. Have it replaced and you'll be good.
Hope this helps and thank you for using FixYa! Have a good one!

Jun 01, 2011 | Suzuki Grand Vitara Cars & Trucks

1 Answer

Why wont my reverse lights stay on if they work?


Hello,

if your reverse light don't stay on, first check the bulb.

If the bulb is okay, check the reverse light wire and make sure its intact.

Lastly, check your fuse box. You should find your fuse box under your steering and or inside the bonnet. Check if the fuse has blown.

Good luck.

Nov 26, 2010 | 1987 Dodge Aries

1 Answer

Dash light


It sounds like the headlight switch is bad.

Apr 22, 2010 | 2000 Mitsubishi Eclipse

1 Answer

The back up lights are not working. could it be


Most likely its the fuse. Check it and replace it if needed. If the fuse is good, check the light bulbs. If the bulbs are good, check the wires on the switch by the break pedal (this switch is monted above the break pedal, just follow the lever where the pedal is mounted all the way up until you find the switch). If the wires are connected, use a tester to see if the switch is working when activated.

Oct 18, 2009 | 1996 Mitsubishi Eclipse

2 Answers

Back up lights on my eclipse dont work.


Are the bulbs good and is the fuse good? If they're both good, then the odds are the reverse switch has gone bad. The switch is located on the side of the transmission and will have several wires coming out of it

Sep 15, 2009 | 2001 Mitsubishi Eclipse

1 Answer

95 Chevy truck tail lights don't work; everything else- brake, turn, backup & hazard do.I checked fuses in dash, replaced headlamp switch-still won't work.


check the bulbs they are a duel fillament bulb possibly have wrong bulb or one side is burnded out. if I remeber correctly the part No#3157 it should be stamped on base of bulb these should be the 2 top bulbs.the lower reverse light is a single fillament part No#3156 also check the sockets and plugs for a good connecton.

Jul 02, 2009 | 1995 GMC Suburban

3 Answers

Tail light, backup light and dashboard light will not light up??


96 eclipse rs back tail lites and dash wont come on i changed the combination switch ,fuses,relays and bulbs and it still dont work what else can it be?

Dec 11, 2008 | 1997 Mitsubishi Eclipse

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...