Question about 1990 Ford F150

1 Answer

I have been trying to figure out what the signal light stick is called and I want to fix it to where it stays down when I signal

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 66 Answers

This is part of the turn signal switch cam plate in the steering collumn. Be carefull replacing this yourself. You'll need special tools to pull the sterring wheel and there other switches involved there. The plastic cam on the plate is broken or worn and needs to be replaced.

Posted on Mar 16, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Brake lights stay on 1995 nissan quest van

if you have changed out the brake light switch try looking up where the pedal is attached to the car i had a honda and there was a little clip that when the brake isnt pushed it would shut the brake lights off and so when i figured it out i just fixed it by sticking a fender clip in its replacement and it worked.

Feb 21, 2012 | 1995 Nissan Quest

2 Answers

How do i turn off my high beams on my 2004 monte carlo?

The daytime running lights are on whenever the key is on and they use the high beams at reducd voltage. Turn the lights on at night and the turnsignal stauk pushed to the speedometer is high and back towards the driver is low. turn the lights off and the highs come on at reducd voltage as the daytime running lights. It's law in most states and many countries to run with the lights on if the car is moving. Pushing down just one click on the parking break pedel should turn them off. the ambiant light senser can be bad or damaged and the high beams stay on the senser is i the center of the dash right up to the windsheild, If it detects darkness it should switch the lights to full power lowbeams. automatically. there is no turn off for the lights except to turn the key off. If they stay on with the key off and the light switch off then the headlight relay can be sticking and its in the underhood fuse relay center and it's location is marked on the lid and it's called the DRL relay their are other relays in the box so you can just substute a different one to see if that will fix it and if it does get a new relay. the lights should work normally if they are turned on and the high beams should be brighter.

Sep 17, 2010 | 2004 Chevrolet Monte Carlo

1 Answer

How do you change turn signal bulb on an 88 comanche. cant figure out how to get too it.

which turn signal the front or back if its the back try looking fdor a apartment and stick your hand back towards your lights this should take you right to it, if front then try un screwing the big black nut on top of the signal this should open both the headlight and turn signal. :)

Mar 23, 2010 | 1988 Jeep Comanche

2 Answers

Tiburon 04, left turn signal lights stay on once activated by either turn switch, hazard light switch, or alarm. Can sometimes get them to go out by using right turn switch position, or playing with hazard...

replace the turn signal 'Clicker' also known as the turn signal relay. Most likely the problem unless you have a really wierd electical issue that will be hard to isolate...


Jan 23, 2010 | 2004 Hyundai Tiburon

1 Answer

Driver side signal light

Change the bulb from the back. Just lay down and look up. Squeeze the nylon clip, and turn the socket counter clockwise, and it'll pop out.

Jul 06, 2009 | 1998 Chevrolet Blazer

1 Answer

Toyota Camry 1991 door light stays on

You need to readjust the switch on your trunk door, or replace. To check it locate it, tape it down with duct tape and see if the light goes off. If not it's bad. If it does it means it isn't sticking out far enough to be turned off when the trunk is closed. The adjusment should be fairly obvious. If not you can simply unplug it which has the same result as turning it off.

May 11, 2009 | 1991 Toyota Celica

1 Answer

Check engine light stays on

On your egr tube you'll see two little black hoses that go up to a sensor.That sensor usually causes the problem and will be undetected by a scanner.It corrodes and sticks the sensor wide open. change that part and your problem will be fixed...

Apr 01, 2009 | 1997 Ford Explorer AWD

1 Answer


I just found out today that it is a problem for alot of 2003 tiburons that the flasher relay for the turn signals will go out causing the turn signal lights to stay on even with the car off. The relays are internal and located on the circuit board of the BCM. In order to fix you will have to remove and disassemble the bcm circuit board from it's housing and resolder a new flasher relay. Haven't figured out where to get that flasher relay though.

Jan 19, 2009 | 2003 Hyundai Tiburon

Not finding what you are looking for?
1990 Ford F150 Logo

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides