Question about 2000 Jeep Grand Cherokee

1 Answer

Go on with 1st. gearand those not change at all. already replace with a new automatic transmition but same result.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 55 Answers

Is the check engine light on? In event of a failed speed sensor, the transmission can go into limp mode. That leave you with one forward gear, usually second, and reverse.

Posted on Mar 16, 2011

  • giuseppetrup Mar 17, 2011

    thank you,but where is exactly the speed sensor placed ?

  • sasilvertree Mar 18, 2011

    It seems that on your model, both of the input and output speed sensors are on the transmission. So if you have replaced the transmission with a new one, the sensors would be new also. But there are several other electronic failures that could cause your transmission to go into limp mode. Sometimes the peramiters have to be reset from the old transmission to the new one. Most transmission shops would be happy to scan your jeep for a small fee or possibly free...The information you need could be there at the press of a button. Good luck



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why does it jerk between 1500 and 2000 rpm while changing gears (automatic)?

Hi,sometimes this can be becouse the filter and transmition fluid need changed,people tend to ignore this area but its just as importent as changing the engine oil and filter,also there is a additive you can use that helps to make things run better inside the transmition its cald,(xado)you can find this on ebay,I drive a mercedes and always use this product it dose work.
I hope this was some help,and just to say I dont sell or make any money from these people who sell xado I just know that it works,all the best.

Nov 12, 2015 | 1994 Volvo 940

1 Answer

Do chevy 350s already have a cluch pilot bearing in them even if its an automatic transmition

They put pilot bearing in at the factory so the motors can have any trany instaled in production and not need to program one in.

Jun 07, 2012 | GMC Jimmy Cars & Trucks

1 Answer

There is a whirring noise and the gears don't seem to be kicking in. The car is an slk automatic

It seems that your clutch plates have worn out. The automatic gears system uses a centrifugal clutch which automatically engages as the engine rpm increases. If the the plates are worn out, it will make a whirring sound as you rev the engine & there will be a loss of power transmitted to the wheels resulting in slow pick up of speed. Get the clutch plate assembly replaced.........sodeep

Nov 02, 2010 | 2001 Mercedes-Benz C-Class

1 Answer

My 96 mercury sable will not go out of 1st gearand i got a P0743 code is it the speed sensor and if so where at on the transmission is it cuz i cant find it it has the ax4n transmission

Most of the time its the wires going to speed sensor. Passenger side rear of engine, under altenator (way down). My shoop usaully only charges about $75 to fix that issue.

Jan 18, 2010 | 1996 Mercury Sable

1 Answer

Transmition has a had time shifting is automatic

the mechanic should check the shifting gear and the shifting lever or the shift level and also the gear sleeve. Gear sleeve is the one that make the gear function. And lastly don't forget the transmission sensor because sometimes the problem can be found in the sensor .Then try to check the 1st. gear, 2nd gear,3rd gear,N ,R.of the trans mission to be sure .

Aug 16, 2009 | 2002 Oldsmobile Alero

2 Answers

1988 Chevrolet K1500, 4x4, Auto transmition will not shift into 3rd, or higher

try adjusting kickdown cable to manfactures spec this may work

May 29, 2009 | 1988 Chevrolet K1500

3 Answers

Automatic Transmition Wont Shift automaticly

sounds like the governer gear stripped out , its located on the driver side on the trans where the axle inboard shaft goes into the trans

Dec 19, 2008 | 1989 Toyota Camry

1 Answer

Transmition pan removal/ filter for 1994 honda accord 2.2 v tec

1st thing to check is fluid level. I am assuming this is an automatic. Drive car 20 minutes to warm up, w/ engine off and car in park. Unscrew the dipstick, wipe w/ clean rag, re-insert, DO NOT screw it in, pull out and check level. Add if necessary. Low level can cause slipping. Replace (screw in dipstick). If you still have trouble, you can drain the fluid, refill and see if that helps. As far as I know, there is no filter on this year and model to change.countrycurt0

Aug 05, 2008 | 1994 Honda Accord

3 Answers

Automatic transmission problem

I have 1998 Maruti Esteem Automatic gear car - It works smoothly for 10-15 Kms and afterwards gear not shifting (may be getting heated inside somewhere?) - Recently I changed gear oil also. Any solution???

Jul 01, 2008 | 1997 Suzuki Esteem

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides