Question about 1992 Oldsmobile Cutlass Supreme

1 Answer

Rear strut mounting bracket replacement - 1992 Oldsmobile Cutlass Supreme

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Oldsmobile Master
  • 1,249 Answers

This can be purchased seperately from your local parts store...not recommended to change strut without replacing the strut mount too...Hope this helps. (About $25.)

Posted on Mar 16, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install the alternator belt in a 2008 Suzuki xl-7?


which engine option, you do know belts are not same on all engines right? fact.
2.7L V6 or bigger? IDN.

same on all cars. (answering in generic form do to above)
loosen the tension-er.
take off old
put back new
and if not a spring tension-er,set proper tension
the fSM cover all this.
why not read the manual, RTM?

here is one example (get the book, RTM or see alldata.com)

2008 xl7 engine


Removal Procedure

Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .

Install the engine support fixture. Refer to Engine Support Fixture .

Remove the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

Remove the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Remove the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Lower the vehicle


Rotate the drive belt tensioner clockwise to release the drive belt tension.

Slide the drive belt off of the belt idler pulley (1).

Slowly release the drive belt tensioner.

Remove the drive belt from the accessory drive pulleys.

end remove
beg, install



Install the drive belt to the crankshaft pulley, the tensioner and the generator.

Rotate the drive belt tensioner clockwise.

Install the drive belt to the idler pulley (1).

NOTE

Important: Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.

Slowly release the drive belt tensioner.

Raise the vehicle.

Install the right side engine mount bracket. Refer to Engine Mount Bracket Replacement - Right Side .

Install the engine splash shield. Refer to Engine Splash Shield Replacement - Right Side .

Lower the vehicle.

Install the engine mount strut bracket. Refer to Engine Mount Strut Bracket Replacement - Right Side .

Remove the engine support fixture. Refer to Engine Support Fixture .

Install the the air cleaner assembly. Refer to Air Cleaner Assembly Replacement .
end.

Sep 07, 2014 | 2008 Suzuki XL7

1 Answer

How to remove a radiater from a 2000 oldsmobile silouette?


Hello,
  • Remove air cleaner and duct assembly.
  • Drain coolant into a suitable container.
  • Loosen engine mount strut to engine mount strut bracket bolts.
  • Loosen engine mount strut bracket brace bolts from upper radiator support bracket.
  • Remove mounting bolts on radiator upper support and position engine mount strut and bracket to rear.
  • Ensure ignition switch is in Off position, then disconnect cooling fan.
Thanks

May 20, 2011 | 2000 Oldsmobile Silhouette

1 Answer

How do I change the rear shock on my 1999 Dodge Neon?


  1. Raise and safely support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Unfasten the retainer(s), then remove the hydraulic flex hose bracket from the strut bracket. If equipped with ABS, the wheel speed sensor cable routing clip is also attached to the strut assembly bracket.
  1. Support the rear knuckle, suspension and brake components before removing the clevis bracket-to-knuckle attaching bolts. Do NOT allow the weight of the knuckle and related components hang without support when the strut is removed.


  2. WARNING The knuckle-to-strut attaching bolts are serrated and must not be turned during removal. Remove the nuts while holding the bolts stationary in the knuckle.
  1. Hold the bolt with a wrench, then unfasten the 2 clevis bracket nuts attaching the strut to the knuckle.
Fig. Fig. 2: Location of the knuckle-to-clevis bracket bolts


  1. Carefully lower the vehicle, then open the trunk. Access to the rear upper strut mount-to-strut tower attaching bolts is through the trunk of the car.
  2. If necessary, remove the carpet from the top of the strut tower. Then, remove the rubber dust shield from the top of the strut tower for easier access to the upper strut nuts.
  1. Loosen, but do not remove the 4 upper strut mounting nuts. Then, while supporting the strut assembly, fully remove the 4 strut mount attaching nuts.
  1. Remove the strut assembly from the knuckle by sliding the knuckle out of the clevis bracket on the strut, then remove it from the vehicle.
Carefully pull the strut assembly out of the vehicle
To install:
  1. Position the strut back into the vehicle with the 4 studs on the strut mount assembly through holes in the strut tower of the vehicle. Install the 4 strut mount-to-body attaching nuts onto the mount studs. Tighten the nuts to 25 ft. lbs. (34 Nm).
  2. Install the dust shield into the opening on top of the strut tower. Install the carpeting back on top of the rear strut tower.
  3. Raise and safely support the vehicle.
  4. Install the knuckle into the clevis bracket on the strut assembly. Install the 2 clevis bracket-to-knuckle attaching bolts and nuts. Hold the bolts with a wrench while tightening the nuts to 70 ft. lbs. (95 Nm).
  5. Install the brake hose bracket to the strut bracket and secure with the retaining bolts. If equipped with ABS, the wheel speed sensor cable routing clip is also attached to the strut bracket.
  6. Install the wheel and tire assembly on the vehicle. Tighten the lug nuts evenly, in sequence, to 100 ft. lbs. (135 Nm).
  7. Carefully lower the vehicle.
  8. Have the toe checked and adjusted as necessary.

Nov 05, 2009 | 1999 Dodge Neon

2 Answers

On a 1989 nissan maxima with sonar suspension II how do you disassemble the strut assembly? the mounting bracket for sonar adapters is in the way of the strut center bolt.


First you must remove the rear seat to gain access to the top strut mounts. The bottom of the rear seat comes out first. On the 91 model there are two tabs at the base of the seat bottm that you pull forward to release the seat bottom. I'm not sure if the 89 is the same. After removal of the rear seat bottom, you will see a bolt at the bottom of each side of the rear seat back that need to be removed. Fold down the arm rest and disconnect the vinyl cover at the base of the armrest to expose and remove two screws. Push up on the rear seat back to unhook three plastic hooks (center and one at each end) at the top of the rear seat back. Remove the seat back. Remove the large metal support panel that is behind the seat back. Safely jack up the rear of the car and support on jack stands so the rear wheels hang free. Doing one strut at a time, remove the two top strut mount bolts leaving the center strut stud nut in place. The strut and mount will lower out of the unibody. Disconnect the bottom strut mount. Remove the strut/coil spring assembly. Using a strut/spring compressor (some auto parts stores rent these) compress the spring. Carefully remove the top strut stud retaining nut, top strut mount, bumpers and strut boot. Carefully install compressed spring, strut boot, bumpers and top strut mount on new strut and install washer and retaining nut. Reinstall strut and etc. in reverse order.

Sep 15, 2009 | 1989 Nissan Maxima

1 Answer

How to replace 2000 mercury sable sway bar links


It does require loosening of the sway bar mounting bolts. If you don't there is no way you will get this job done.Good Luck.

Aug 22, 2009 | 2000 Mercury Sable

2 Answers

How do you change the rear struts in my 95 Olds Cutlass supreme? Is this something I could do myself or would I be better off taking it to a mechanaic?


Many of the 95 Cutlass Supremes have a transverse leaf spring suspension on the rear and there are no coil springs. I believe it depends on whether it is a 2 door or 4 door model. It is much easier to do the struts on the transverse leaf spring type. Support the knuckle with a jack or jack stand. Unbolt the upper mounting bracket by removing 2 bolts from inside the wheel well. Then remove the 2 bolts holding the bottom of the strut to the knuckle. Now you can remove the upper mounting bracket from the strut and place it on the new strut. Reinstall by reversing the procedure.

You can also leave the upper mounting bracket on the car and just unbolt the strut, but this can be more difficult. Support the knuckle with a jack or jack stand. Use a torx socket to keep the strut shaft from spinning and remove the upper mounting nut. Now remove the 2 bolts holding the bottom of the strut to the knuckle. Reinstall by reversing the procedure.

Jun 07, 2009 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Rear struts and brackets


2002? heck yes it is worth fixing. here in calif that is a very new car.

May 31, 2009 | 2002 Chrysler Sebring

2 Answers

Insturctions for replacing rear struts


raise rear of vechicle then support by jack stands.let rear suspension hang to take pressure off strut coil springs.remove rear package tray trim panel. remove rear wheel.remove brake load sensor .remove brake hose.remove stabilizer bar bracket and link.remove tension strut .remove spindle pinch bolt and strut assembly.if the strut coil spring broke you wont need a coil springcompressor.BESURE INSTALL NEW MOUNTING BOLTS AND PINCH BOLT.install the strut assembly.use a new pinch bolt .torque it to 50-67 ft lbs.torque the 3 upper mounting nuts to 19-25 ft lbs. tension strut torque nut to 35-46 ft lbs. stabilizer bar link torque to 60- 81 inch pounds.stabilizer bar bracket torque to 25-33 ft lbs.NOW INSTALL .brake hose / brake load sensor/ rear wheel /rear package tray trim panel.

May 31, 2009 | 2000 Mercury Sable

2 Answers

Replace rear struts 1996 buick regal


Here is a link describing your strut replacement. Autozone also has free tool rental for the strut spring compressor if you need it. Thank you, and don't forget to vote. http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800681ba

Jan 29, 2009 | 1999 Buick Regal

Not finding what you are looking for?
1992 Oldsmobile Cutlass Supreme Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...