Question about 2000 Pontiac Montana

1 Answer

I bought a hitch for the rear to pull a hot dog cart. We just can't figure how to wire the breaks to it. We are trying to follow the directions but getting nowhere.

Posted by on

1 Answer

Not what you want to hear,but a travel center
or trailer rental place,do that every day

So I would go there, at least for advice

Posted on Mar 16, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Iv got an 89 gmc pickup and my tail lights arnt working my headlights an all work fine but my tai lights have no running lights no blinkers and no break light and I checked all the fuses under the das


In my opinion as long as you've checked all the fuses I would say it could possibly be the ground which will either be on the rear portion of you frame or close to your receiver if you have one. That can make all of your lights not work at the same time but if you have anymore questions just ask

Nov 22, 2012 | Cars & Trucks

1 Answer

How do you hook up trailer lights so i can pull a trailer


If you bought the Honda hitch kit, a wiring harness and instructions are included. If you bought a different kit, buy the wiring harness from Honda. The harness connects to a plug located in one of the accesses panels in the back. You will have to take off the. Bumper facia to route the harness to the hitch. Be sure to use the rubber grommets to prevent the sheet metal of the rear quarter panel from wearing through the wire insulation and causing a blown fuse.

Aug 07, 2011 | 1997 Honda Passport

1 Answer

I have an 03 Toyota Sequoia, 4.7L V8, factory installed hitch receiver and wiring. The manual says it has a towing capacity of 6500 lbs GVWR. I have been towing a popup trailer weighing 3000 pounds with no...


I think the tongue weight rating on the stock hitch is 600 lbs, so you are over that. You probably want to level out truck to handle better when towing, so the best way is to get air bag helper that raises the back end.

Sep 20, 2010 | Cars & Trucks

1 Answer

I bought a new 2001 one ton chassis and had a flat bed put on it. They installed a 4 prong female plug(the round kind) for trailer lights. The other day I tried some of those temporary magnetic lights on...


I would look under the rear of the truck to see if the brake wiring got pulled off. When hitch plugs are installed they have to tap into your brake wires. If they fell off they might have pulled all of the wiring loose so nothing will work.

Sep 07, 2010 | 2001 Chevrolet Silverado 3500

1 Answer

I have 2003 kia sadonna, rear tail light and licence plate lamp don't light up. Everything else is Okay, brakes and signal etc. I checked fuses they all seem to be okay, Allthough on my vechicle where it...


Hi, you have a cut or damaged wire between the left tail light and the license plate. This could have been caused by the hitch installation. The hitch is using the same fuse.

Jun 12, 2017 | 2006 Kia Sedona

1 Answer

Were do you hook up the two wires under the hood for trailer brakes on a 2000 silverado


Sometime around 2000, GM started putting trailering pre-wire harnesses in the vehicle. Your truck may have this harness built in and would greatly simplify brake controller installation. Look under the glovebox and see if there is a wire harness tied off. There will be four wires in this harness, which should be run over to the steering column to use it. Most trailer brake controllers are compatible with this harness.
The four wires in the harness are: Red, 12vdc; black, ground; blue or purple, brake pedal; and brown or white, trailer brake wire to seven pin, four pin, or five pin connector at trailer hitch, if your truck came from the factory with a trailer hitch.
If you are adding the hitch and do not have the four wire harness, the under hood wires from your brake controller are Red, connect to one of the studs under the distribution box cover (the distribution box is on the driver's side against the firewall. Underneath the cover are two large threaded studs which are hot from the battery all the time); and the other wire from your brake controller would have to be run the length of the truck along the frame, tied off in several places, to the trailer hitch connector on the bumper. Follow the directions that came with trailer hitch wiring connector to connect this wire to the proper pin in the connector.
If this has helped you, great, and please remember to vote/comment.
Good luck!

Feb 21, 2010 | 2000 Chevrolet Silverado 1500

2 Answers

Wiring for hitch


most of these trucks came with the wiring harness for trailers already there,look in the back whre the wires feed the rear lights,you should find a connector there, just go to your local parts place and tell them you need the trailer connector for your truck, should just plug in. if you need more help let me know Ray

Apr 15, 2009 | 2002 Chevrolet Silverado

1 Answer

1997 f150 flairside right rear break and turn signal light


Try pulling out your tail light then following your wires. you should have four going into the socket one for running light, brake light, and turn, follow those down. till you find where they go and if they keep going then those are not your ground. go back to the socket and take that last wire that runs down follow it till you get to the spot that it is grounded to and some times it will be grounded in with your license plate lights. if not directly to the frame

Mar 24, 2009 | 1997 Ford F150 Regular Cab

1 Answer

CANNOT RECEIVE FM SIGNAL


no fmm signal and am static more than usual antenna is disconnected

Nov 06, 2008 | 2002 Hyundai Santa Fe

Not finding what you are looking for?
2000 Pontiac Montana Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...