Question about 1997 Chevrolet Blazer

1 Answer

Engine will turn over but will not ignite - 1997 Chevrolet Blazer

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Contributor
  • 299 Answers

See if you have spark at the plugs , start there, try this also ....turn key to on position listen for buzz at fuel tank, if no buzz it needs a fuel pump.

Posted on Mar 16, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Recode car key



30 MINUTE RELEARN PROCEDURE
  1. Turn ON the ignition, with the engine OFF.
  2. Attempt to start the engine, then release the key to ON, vehicle will not start.
  3. Observe the SECURITY telltale. After approximately 10 minutes, the telltale will turn OFF.
  4. Turn OFF the ignition, and wait 5 seconds.
  5. Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.
  6. Important: The vehicle learns the password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
  7. Start the engine. The vehicle has now learned the password.

Feb 01, 2014 | 2006 GMC Sierra

1 Answer

Key stays in ignition and will not turn off engine


you need to replace the ignition switch
Not a simple deal ....
LB

Sep 22, 2008 | 1991 GMC Suburban

2 Answers

2000 Hyundai Excel ignition lock problem


What most people refer to as the "Ignition switch" is really the "cylinder lock", that when turned with the key, operates the actual "ignition switch".
The switch causing your problem is inside the steering column, and the column needs to be at least partly disassembled to access it.

Jan 25, 2014 | 1994 Hyundai Excel

1 Answer

Resetting the passlock


1. First, insert the ignition key and turn the ignition switch to the "On" position (Do not start the engine). Leave the switch on for 11 minutes. The security light may flash or be on steady during this 11 minute period. Make sure the light is no longer on or flashing before proceeding to #2 .
2. Turn the ignition switch off for 30 seconds.
3. Turn the ignition switch to the "On" position (as in step #1) for 11 minutes again.
4. Turn the ignition switch off for another 30 seconds.
5. Turn the ignition switch to the "On" position for 11 minutes a third time.
6. Turn the ignition switch off for 30 seconds one final time.
7. Turn the ignition switch to the "On" position one final time and wait 30 seconds.
8. Attempt to start the engine. If the engine starts and runs normally, the relearn is complete. If the engine does not start, Go to this link for info
http://vatspasslockpasskeysecurityhelp.yolasite.com/

Sep 08, 2012 | 2000 GMC Yukon Denali

1 Answer

My maintenance light is still on even though i have changed my engine at 60,000 mileage, what could be the problem and how can i make it stop (toyota corolla 06)


To reset Maintenance light, do the following procedure:

  1. Turn the ignition to run (one position before starting engine).
  2. Ensure odometer reading is shown. Turn ignition off.
  3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
  4. Hold down knob for at least 5 seconds. The odometer indicates "000000" and the light goes off. If the system fails to reset, the light will continue flashing.
  5. Turn the ignition off and then start the engine to verify the indicator has been reset.

Apr 13, 2012 | 2006 Toyota Corolla

1 Answer

Ignition troubles


unplug connector at ignition switch, bridge terminal 30 [battery power] on connector and terminal 50 power to starter solenoid. engine should turn over. plastic ignition switch can wear and not make contact. at times the lug on ignition barrel that turns the switch breaks off.

May 23, 2010 | 1996 Volkswagen Jetta

2 Answers

When it starts .. it won't stay started.


ENGINE NOT STAY RUNNING.COULD BE STOPPED UP FUEL FILTER BAD FUEL AND .FAULTY OR INCORRECT GAP PLUGS.ALSO BAD SPARK PLUG WIRES.FAULTY IGNITION SYSTEM.USE A DIAGNOSTIC SCANNER TO CHECK IDLE SPEED CODES AND MASS AIR FLOW SENSOR PROBLEMS.

Oct 16, 2009 | 2005 Chevrolet Malibu

2 Answers

1995 Ford Mustang Engine Won't Turn Off


the ign switch should take care of it i agree with you

shack

Apr 18, 2009 | 1995 Ford Mustang

Not finding what you are looking for?
1997 Chevrolet Blazer Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...