Question about 1993 Ford F150 SuperCab

1 Answer

Cant get the oil pan off a 302 - 1993 Ford F150 SuperCab

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You have to jack the engine up after removing the motor mount bolts on each side. Then once you have the engine jacked up a few inches, slide a piece of wood (2x4) in between the upper and lower parts of the motor mounts on each side. This will keep the engine elevated enough for you to drop the oil pan and replace the gasket. Then, just put all the bolts back in in the proper torque sequence, torque them all to spec,remove the wooden blocks from the motor mounts, slowly lower the engine back down and put the motor mount bolts back in.

Posted on Mar 24, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram of ford 302 oil pan pattern of tighting oil pan bolts


There isn't a sequence but I would install all the bolts finger tight, then start from the center of the pan and work your way out with even torque. @ about 18ftlbs

Feb 27, 2015 | Ford Cars & Trucks

1 Answer

Where is the oil drain plug on a 2004 mercedes sl500 302 HP V8


It has to be at the lowest point of the oil pan. Perhaps a cover blocks you seeing it?

Dec 12, 2014 | Cars & Trucks

1 Answer

Is there more one oil drain plug in a 1978 Ford Fairmont and do you need to drain both pans? 302 engine


That vehicle is too old to look up online, but some of the older Ford engines (particularly the 302 or 5.0L) were eqipped with 2 drain plugs on the oil pan. One is way up front by the crankshaft pulley and the other is in the bottom of the pan in the usual place. Yes, it is required that you drain BOTH of them. You will leave about 1-1/2 quarts of old oil in the engine if you don't.

Jul 09, 2011 | Ford Fairmont Cars & Trucks

2 Answers

The left front exhaust valve hydraulic lifter on my 302 cleveland has taken the bottom off it and i want to know where it could end up


First of all Ford never made a 302 cleveland, they made 351 cleveland . the metal from the lifter is all thru the engine ? ( bearings, oil pan, etc. )

Apr 21, 2011 | Ford Futura Cars & Trucks

1 Answer

Cant locate starter motor where is on 302 cleveland


The starter is on the right hand side of your engine (passenger side in North America), down tight beside the oil pan, and bolted into the bell housing. You will have to get underneath the car to see it, as it will be hidden by the frame and exhaust from the top.

Mar 04, 2011 | Ford F-150 Cars & Trucks

1 Answer

302 ci. 5.0 ltr . oil pump replacement


Why do you want to replace the oil pump? I am asking this question for good reason. Engines that have worn bearings will have low oil pressure, and replacing the pump will not solve this problem. If you are replacing the pump because of low pressure, then you really need to consider correcting the cause of the low pressure. To replace the pump, you need to remove the oil pan from the bottom of the engine, which will likely involve raising the engine. Once the oil pan is off, you can readily remove and replace the oil pump.

Aug 24, 2010 | 1998 Ford Explorer

1 Answer

Would like to change oil pan on 1990 ford crown vic 5.0 302 cu/in how do i begin


Before you do, why do you want to change the pan? OK then, consider the sump, is it front or rear? Do you have room to drop the pan 6 inches and get it out? The oil sump is at the bottom of the pan. If not, you have to pull the motor mount bolts out and jack up the engine. Then pull it out. When you put in the new pan, use no adhesive on the gasket, none. Bolt that baby up, drop the engine, tighten everything up, fill her up with oil, you should be all set.

Aug 13, 2010 | 1990 Ford LTD Crown Victoria

1 Answer

Ford 302 engine


Sounds like the fuel pump is not working. I would find myself a repair manual and start reading about troubleshooting. If not interested in that I would call a repair shop.

Mar 10, 2009 | 1986 Ford F150 SuperCab

2 Answers

Noise at bottom of oil pan


Hello Josh thank you for using FixYa for your answer my name is David.
sounds to me like it Has something to do with the oil pump or the maybye even the screen here is a list of things it may be.
1 Inspect Valve Lifter Insufficient oil supply to valves and lifters. grey_line.gif 3 Inspect Rocker Arm Worn or incorrectly adjusted rocker arm(s). grey_line.gif 4 Inspect Rod Bearing Incorrect rod or main bearing clearances grey_line.gif 5 Inspect Oil Pump Damaged or faulty oil pump grey_line.gif 6 Inspect Oil Pump Drive Gear Damaged or faulty oil pump drive gear grey_line.gif 7 Inspect Oil Pump Screen Clogged oil pump screen grey_line.gif 8 Inspect Engine Oil Capacity Low engine oil level

Nov 09, 2008 | 1996 Ford F150 Regular Cab

Not finding what you are looking for?
1993 Ford F150 SuperCab Logo

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...