Question about 1998 Ford Contour

1 Answer

Fan motor how do get to the fan motor to remove it

Posted by on

  • erniesew Aug 06, 2008

    I didn't get an answer on my return. I don't know if something went wrong or what.

×

1 Answer

Cooling fan or blower motor?

Posted on Aug 03, 2008


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Want to change fan on blower heater


Removal

  1. Remove wiper arms.
  2. Remove cowl panel.
  3. Disconnect blower motor electrical connector and vent tube.
  4. Remove blower motor retaining screws.


  1. Remove fan retaining nut from blower shaft through plenum opening while holding the fan from the engine compartment.
  2. Remove fan from blower motor while removing blower motor from vehicle.
Installation

  1. Hold fan through plenum opening.
  2. Install blower motor to vehicle while installing fan to blower motor.
  3. Install fan retaining nut to blower motor shaft through plenum opening.
  4. Install blower motor retaining screws.
  5. Connect electrical connector and vent tube.
  6. Install cowl panel.
  7. Install wiper arms.

Aug 13, 2013 | 1991 Oldsmobile Cutlass Ciera

2 Answers

Need to replace radiator fan and its motor


need to remove the fan unscrew the fan center nut and remove fan blade from motor.to remove fan motor from shroud remove the three mounting screws in back of fan motor.

Jan 25, 2013 | 1997 Honda Civic

1 Answer

Is there a fan clutch on a 2000 toyota solara


NOPE YOU HAVE TWO ELECTRIC COOLING FANS. YOU HAVE TO REMOVE FAN SHROUD FROM RADIATOR THEN YOU HAVE TO REMOVE FAN FROM MOTOR USING SOCKET AND WRENCH.HOLD FAN WITH HAND WHILE LOOSEN FAN NUT.AFTER YOU REMOVE FAN BLADE YOU HAVE TO REMOVE THREE SCREWS HOLDING FAN MOTOR TO SHROUD.

Jun 20, 2011 | 2004 Toyota Solara

1 Answer

How do you remove and replace a heater fan motor on a 1983 chevy silverado truck?


If you have ac or not the motor is easily accessed by working under the hood. remover the wire connector and then the mounting screws. Pull the motor out and pull the fan off after removing the nut off the fans shaft.. Install the fan on the new motor and reinstall

Apr 20, 2010 | Chevrolet Silverado 3500 Cars & Trucks

1 Answer

Need location on blower motor resistor on 1994 pontiac bonneville


58f261e.jpg

Fig. 1: The blower motor and fan assembly is mounted in the heater and A/C module, and is accessible from the engine compartment

GM Bonneville/Eighty Eight/LeSabre 1986-1999
Blower Motor - REMOVAL & INSTALLATION
(see Figures 1 and 2)
  1. Disconnect the negative battery cable.
  2. If necessary, tag and disconnect the number 2, 4 and 6 spark plug wires from the ignition coil and move the coil out of the way.
  3. For 1993-99 vehicles, remove the nuts and cross brace bar.
  4. Detach the electrical connections from the blower motor.
  5. Disconnect the cooling tube from the blower motor.
  6. Unfasten the screws securing the blower motor to the blower module assembly.
  7. Remove the blower motor and fan assembly from the module.
  8. If necessary, unfasten the nut attaching the fan to the blower motor shaft, then pull the fan from the blower motor.
68515cf.jpg

Fig. 2: You can disassemble the fan from the motor by removing the retaining nut


To install:
  1. If the fan was removed from the motor, position the fan on the shaft, then install the retaining nut. Tighten the nut to 12 inch lbs. (1.4 Nm).
  2. Position the blower motor and fan assembly to the module, then install the retaining screws. Tighten to 5 inch lbs. (0.6 Nm).
  3. Connect the cooling tube to the blower motor.
  4. Attach the electrical connector to the blower motor.
  5. On 1993-98 vehicles, install the cross brace bar and retaining nuts. Tighten the nuts to 18 ft. lbs. (25 Nm).
  6. If removed, install the coil and connect the spark plug wires, as tagged during removal.
  7. Connect the negative battery cable.

Hope this helped (remember rated and comment this).

Mar 26, 2010 | 1994 Pontiac Bonneville

1 Answer

Want to replace the radiator on my 1997 ford thunderbird


Radiator Aluminum Core, Crossflow — 3.8L (Base) and 4.6L Engines
Removal
  1. Drain engine cooling system as described. Disconnect upper radiator hose (8260) and lower radiator hose (8286) and radiator overflow hose (8075) from the radiator (8005). Disconnect the transmission oil cooler inlet and outlet lines from the radiator.
  1. Remove cooling fan motor,fan blade (8600) and fan shroud (8146) assembly as described.
  1. Remove radiator upper bracket retaining bolts and remove bracket. Lift radiator from vehicle.
Installation
  1. Position the radiator into the vehicle. Install upper brackets and tighten bolts securely.
  1. Connect the transmission oil cooler lines to the transmission oil cooler fittings.
  1. Install cooling fan motor, fan blade and fan shroud assembly as described.
Engine Cooling Fan Motor, Fan Blade and Fan Shroud Assembly, Electrical Removal
  1. Disconnect (pull apart) the male-female cooling fan motor wiring connector at the side of the fan shroud (8146). Remove the male terminal connector retaining clip from the fan shroud mounting tab.
  1. Remove two fan shroud upper retaining bolts at the radiator tanks.
  1. Lift cooling fan motor/fan blade (8600)/fan shroud assembly past radiator (8005), disengaging fan shroud from two lower retaining clips.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten fan shroud retaining bolts to 5.2-7.2 Nm (46-63 lb-in).

  2. 10e2638.gif
    8d231fe.gif HOPE THIS HELPS.

    Oct 30, 2009 | 1997 Ford Thunderbird LX

    1 Answer

    The heater in my 2000 chevy malibu is making funny noises ... speeds one and two dont work.. havent since we bought the car... for 2 years now.. but what is that sudden noise that came on yesterday... like...


    I have ran into the same problem, there may be something has got into fan cage. remove fan motor and investagate to see if it is blocked, or if fan is going bad. it is behind glove box, to remove. remove lower right dash insulator panel from under glove box. slide bcm aside for room to get at fan motor. remove 3 screws from fan motor, and remove fan after disconnecting wiring. the blower motor resistor is beside fan motor. the resistor will make ya lose 1 and 2 speeds. for it is a 5 step resistor.

    Oct 29, 2009 | 2000 Chevrolet Malibu

    1 Answer

    HOW DO YOU CHANGE THE HEATER BLOWER MOTOR?


    YOU NEED TO TURN OFF RADIO TO KEEP FROM LOSING RADIO CODE.REMOVE NEGATIVE BATTERY CABLE.THAT WILL DISABLE AIR BAGS.WAIT 30 MINUTES.SO THE AIR BAGS CAN DISCHARGE.THE BLOWER MOTOR IS LOCATED ON THE PASSENGER SIDE OF VECHICLE UNDER THE INSTRUMENT PANEL.WHEN REPLACING THE BLOWER MOTOR.YOU HAVE TO REMOVE THE SQUIRREL CAGE OR BLOWER MOTOR FAN.BY REMOVING THE METAL STAR CLIP RETAINING THE FAN CAGE TO THE MOTOR SHAFT.REMOVE THE FAN BY PULLING STRAIGHT OUT.TO INSTALL BLOWER FAN TO NEW BLOWER MOTOR.INSTALL THE FAN CAGE ONTO THE MOTOR SHAFT .ADJUST THE FAN CAGE TO GET A CLEARANCE OF 0.30 INCH TO THE MOTOR MOUNT PLATE.INSTALL EVERYTHING VISA VERSA.BESURE TO BUY A REPAIR MANUAL.SO IT CAN SHOW YOU WHERE ALL YOUR PARTS AND SCREWS ARE LOCATED. WARNING IF YOU HAVE ANY DOUBT ABOUT THIS TASK.LET THE DEALERSHIP DO IT.

    Oct 13, 2009 | 2005 Chevrolet Impala

    1 Answer

    How do i replace the radiaor? on this 2005 Hyundai do i remove the intake cover, then the cooling fan, the the motor mount? what?


    Below are instructions and a diagram for removing the radiator from your Santa Fe. There's nothing involving the motor mounts. Best of luck and please post back with any questions or just to rate the solution. Greg

    1. Drain the cooling system. Remove the radiator cap to speed draining.
    2. Remove the inlet hose from the radiator.
    3. Remove the transmission oil cooler lines from the retainer clip at the bottom of the cooling fan shroud.
    4. Remove the fan shroud clip from the condenser tubes.
    5. Remove the bolt that connects the fan shroud to the condenser hold down bracket.
    6. Remove the air deflectors from the top of the radiator.
    7. Remove the cooling fan shroud bolts.
    8. Remove the coolant reservoir hose from the radiator overflow neck.
    9. Remove the radiator upper support brackets and bolts that connect to the fan shroud.
    10. Disconnect the engine cooling fan motors electrical connectors.
    11. Remove the cooling fan motors electrical harness from the fan shroud clips.
    12. Remove the cooling fan shroud.
    13. Remove the outlet hose from the radiator.
    14. Disconnect the transaxle oil cooler pipes from the radiator.
    15. Tilt the top of the radiator rearward.
    16. Remove the condenser hold down bracket from the radiator.
    17. Lift the condenser from the mounting tabs on the radiator and position the condenser aside.
    18. Remove the radiator.
    6db9db4.gif

    Aug 11, 2009 | 2005 Hyundai Santa Fe

    1 Answer

    Need to replace the left rad fan motor, any ideas on how to do it if i have the new part?


    1. Remove radiator from vehicle.
    2. Remove fan shroud retaining bolts, and cooling fan motor/blade/shroud assembly.
    3. Remove fan blade retaining clips and blades.
    4. Remove motor mounting screws and motors.
    5. If necessary, remove Constant Control Relay Module (CCRM).
    6. Reverse procedure to install. Torque CCRM screws to 40-56 in lb, and shroud retaining bolts to 24-48 ft lb.

    May 27, 2009 | 1996 Lincoln Continental

    Not finding what you are looking for?
    1998 Ford Contour Logo

    Related Topics:

    85 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    61249 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...