Question about 2004 Isuzu Axiom

1 Answer

Replacing a timing belt on 2002 izuzu axiom xs. Cannot seem to get it installed correctly. Vehicle will not run. Aligning all marks and number 2 cylinder is at TDC. Please help.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How to replace the water pump 2004 Axiom

Posted on Nov 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace timing belt on 2002 kia spectre


Removal & Installation

1.5L, 1.6L (VIN 5) & 1.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belts.
  4. Remove the alternator.
  5. Remove the water pump and crankshaft pulleys.
  6. Remove the timing belt guide plate.
  7. Remove the upper and lower timing belt covers.
  8. Position the crankshaft so that the timing mark is aligned with the timing mark on the engine.
  9. Verify that the I and E mark on the camshaft pulley align with the mark on the cylinder head.
    NOTE
    Do not move the crankshaft or camshaft once the timing marks have been correctly positioned.
  10. If the timing belt is to be reused, mark the direction of rotation on the timing belt.
  11. Remove the timing belt tensioner pulley.
  12. Remove the timing belt.


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-0.gif


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-1.gif


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-3.gif
To install:
  1. Install the timing belt tensioner pulley, move the tensioner to its furthest point and tighten the lockbolt.
  2. Install the timing belt onto the pulleys, as follows, crankshaft pulley first, then the idler pulley, exhaust camshaft pulley, intake camshaft pulley, and the tensioner pulley.
  3. Loosen the tensioner pulley and allow the tensioner spring to apply tension on the belt, then tighten the lockbolt to 28-38 ft. lbs. (38-51 Nm).
  4. Rotate the crankshaft clockwise 2 turns and be sure all marks are still correctly aligned.
  5. Install the remaining components in the revere order of the removal noting the following torque specifications:

    Crankshaft pulley: 9-13 ft. lbs. (12-17 Nm) Water pump pulley: 9-13 ft. lbs. (12-17 Nm)
  6. Connect the negative battery cable.

Feb 10, 2016 | 2002 Kia Spectra

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

3 Answers

At how many miles do I need to change the timing belt on my 2002 Isuzu Axiom?


2002 ISUZU AXIOM MANUAL SAYS
CHANGE THE TIMING BELT AT 100,000 MI FOR NORMAL DRIVING CONDITIONS AND 75,000 MI FOR SEVERE DRIVING CONDITIONS

Sep 07, 2010 | Isuzu Axiom Cars & Trucks

1 Answer

How do i re-set timing for Landcruiser Prado 1KZ engine. I changed the timing belt but the dash board indicator (T-Belt) is still on. How can i get this to come off and know that timing has been properly...


You have to pull the instrument cluster out of your vehicle. At the back of the cluster there are 2 screws that are close together, change the screws around. They are the only 2 screws together. Your timing is set by lining up the mark on the injection pump sprocket to the mark on the engine body. Same with the camshaft sprocket, the mark is at the top, and then aligning your two line marks on the timing belt (Toyota Belt) to these marks. Also I would suggest replacing your pulley. The Tensioner Pulley bolt should be torqued to 35 Nm. You need a vice with soft jaws to tension the tensioner and aligning the holes with a bit of coathanger wire. When you re install your tensioner you then pull out the wire releasing the tensioner. The tensioner bolts should be torqued to 12 - 13 Nm. Hope that helps you. PS - When you are removing your interior mouldings be careful as they are expensive to replace. When you remove your screws and bolts there are a number of clip systems that hold some of the mouldings in place.

Jul 21, 2010 | 1996 Toyota Land Cruiser

2 Answers

I cannot locate the dip stick to check the transmission fluid level on a 2002 izuzu axiom


The 2002 Axiom does not have a dipstick to check the transmission fluid. The holding tank is on the right side by the brake fluid. Check your levels & fill if needed there. It has a "sealed" transmission.

Dec 04, 2009 | 2002 Isuzu Axiom

1 Answer

2002 izuzu axiom- can't find transmission dip stick


i have a 2002 isuzu axiom and i have been having some recent problems with my transmission and it took a while to find out but eventually i found out that it has a closed transmission and there is no dipstick there is a fluid resevoir next to the brake fluid but to get the transmission fluid filled or flushed it has to be serviced at a shop

Nov 11, 2009 | 2002 Isuzu Axiom

1 Answer

Looking for serpentine diagram for izuzu axiom 2.3 V6


On all vehicles since 1984 the v-belt/serpentine belt routing diagram has been on the inside of the hood or on the radiator cross member.

Nov 05, 2009 | 2002 Isuzu Axiom

3 Answers

I need timing specs for 3.5 2002 Isuzu Axiom


I have found that one can mark (Paint pen) the gears and teeth (One tooth and one corresponding belt rib) on each gear prior to removing the belt. You can then overlay the old belt on a new belt and mark the same spots on the new belt and then install the belt so your marks on the gears and belt line up as they did before you removed the old belt. Given that your timing was right to start with....if done correctly, this will work.

May 05, 2009 | 2002 Isuzu Axiom

3 Answers

Cant seem to time my 1990 subaru legacy


your timeing marks are on the block rite abouve the cams on either side and on the block in the middle but line the center mark on the teeth there is a mark not the arrow the arrow is where tdc is the mark is on teeth good luck.

Mar 26, 2009 | 1990 Subaru Legacy

1 Answer

How do you replace turn signal bulb on 2001 Izuzu Trooper?


NOT SURE IF IT IS TRUE ON THIS KIND OF VEHICLE, BUT USUALLY WHEN CHANGING A BULB YOU NEED TO GO UNDER THE HOOD ON WHATEVER SIDE YOU ARE CHANGING...AND THERE WILL BE A KIND OF PLUG INTO THE BACK OF THE ACTUAL LIGHT FIXTURE, IF YOU GIVE IT LIKE A QUARTER TURN IT WILL PULL OUT YOU THEN CHANGE THE BULB AND PROCEED WITH PLUGGING BACK IN. MAYBE THIS WILL HELP!

Jan 10, 2009 | 2002 Isuzu Axiom

Not finding what you are looking for?
2004 Isuzu Axiom Logo

538 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...