Question about 2005 Suzuki Forenza

1 Answer

How to make driveshaft released from passenger side

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 1,975 Answers

Thre's a clip in a groove that makes the shaft stay in place. I have had trouble alot of times. I have had to take a cement chisle and hammer it in to force the old one out. in the picture below, where yo see the screwdriver going in that is where I have ended up forcing a "wedge" in there to separate from the transaxle. It will come out believe me. Sometimes it's just a major pain in the..... Keep up with it and success will happen. i hope this helps you and good luck. here's your picture. From a different vehicle but same concept.


how to make driveshaft released from passenger - clifford224_63.gif

Posted on Mar 16, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 ram 1500 4x4.when i put it four wheel drive high it feels like its in low and back tire on driver side skids


There's something seriously wrong in the transfer case or controls. It seems the rear driveshaft is locked up, and the front wheels are driving. The driver's side rear tire is skidding because it's trying to turn backward - rear passenger rear tire is going forward and rear differential has no option but to turn the driver tire in reverse (driveshaft locked). DON'T TRY TO DRIVE IT. Get it checked out and fixed.

Oct 25, 2016 | Cars & Trucks

1 Answer

How to replace a front axle on a 2002 freelander landrover


1. Remove hub centre disc and remove hub nut with wheel on ground.

2. Jack up affected side (not under lower control arm), remove wheel.

3. Remove two caliper bracket bolts and tie caliper up out of the way.

4. Disconnect outer steering joint.

5. Remove two strut-to-hub bolts and pivot hub outwards to release driveshaft outer drive flange.

6. Place oil catch can under car and carefully pry out inner driveshaft joint and remove driveshaft.

7. Reverse steps with new driveshaft. Remember to replace any lost gearbox / transfer box oil.

Apr 23, 2015 | 2002 Land Rover Freelander

1 Answer

2002 Silverado 1500 push button 4 wheel drive issue Light will light showing it is in 4 wheel drive but it is not. Auto button seems to work though.


2 speed electric shift transfer case problems #1 jack up truck place on 4 jack stands. Start and select 4 high position in drive release brake ad watch front driveshaft does it turn "yes" problem is axle actuator on passenger side of differential not engaging axle shaft. "no" apply brakes bring to a stop engage low range does low range work "yes" internal transfer case problems "no" electric transfer case shifting motor failure.

Oct 26, 2013 | 2002 Chevrolet Silverado 1500

1 Answer

I have a 2007 F150 4X4 CC 65k miles. Had grinding noise in passenger front hub when in 2wd under load and acceleration, sound went away after switching to 4 Hi. Replaced solenoid and actuator on passenger...


Hello, It would not hurt to check and would cost you nothing to do so. The valving controlling the vacuum to the actuators could be giving you partial engagement. But if only on one side is doing it, I would think it would pull to the passenger side when in 2 wheel drive.

I had a client with a similar noise and on his truck the front driveshaft had a bad u-joint. Because the driveshaft is to your right, at the center of the truck; he also blamed the passengers wheel. You get a lot of sympathetic motion in the drivetrain. If you think about it, wear can occur on one side of the u-joint. When the shaft is being dragged along by sympathetic motion the driveshaft is being pulled, but when you hit 4x4, now the shaft is pushing and the pressure shifts to the opposite side of the u-joint. Under pressure the joint is now tight.

You may observe rust and grease "tracking" in the areas of the U-joint when you check the front driveshaft. I hope my solution is very helpful in solving your problem. Would appreciate a note when you find the cause of this problem.

May 04, 2011 | 2004 Ford F150

1 Answer

How to replace or install a nissan quest 1997 axle


two axles, different for ach side. Passenger side has a carrier on the half shaft, driver side is one solid link. Loosen lug nuts, the you need a 36mm socket to loosen the center nut on the drive shaft, same for both sides. Remove the cotter pin and retainer before loosening the center nut. Jack up the vehicle and secure with jack stands. Remove wheels. Remove brake calipers and tie up out of the way. Loosen and remove lower strut bolts (2) and lower ball joint bolts (3). Swing center knuckle out and off the drive shaft. On passenger side, loosen carrier bolts (3) halfway up the drive shaft, above the exhaust pipe and crossmember. This is a pain on the 94, but easier on later models. The passenger shaft has two half shafts joined at the carrier. No retainer clip is used, so pull on the end of the shaft and it will come out. Iff the inner CV boot is puked, it will probably come out in two pieces. You may have to use a large screwdriver to pry the inner shaft out of the transaxle. The driver side does not use a carrier and will come out with a strong pull. It does use a retainer clip on the inside end of the driveshaft. You can get new driveshafts with cvs as an assembly at most auto parts stores Be sure the new driver side shaft has the new retainer clip on it. Assembly is reverse of dissassembly, but make sure to tighten everything up good.

Feb 26, 2010 | 1997 Nissan Quest

2 Answers

Toyota shakes on rear passenger side during take off, but I have replaced diff and passenger axle


Hi,could you send more details of the car such has the modle and c.c. and is it a 4x4?
thanks
George

Jul 13, 2009 | 1987 Toyota Supra

1 Answer

Passenger side front brake caliper is not releasing.


well your brake porportion valve is not working right oh well good luck

Jun 03, 2009 | 2005 Dodge Caravan

1 Answer

Passenger side hood will not release


Hood latch on passenger side needs adjusting, Have someone put pressure on side of hood when
you are pushing the hood latch release.
This may help them when they are pulling up on the hood.

May 09, 2009 | 1985 Chevrolet Corvette

Not finding what you are looking for?
2005 Suzuki Forenza Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...