Question about 2004 Chevrolet Monte Carlo

1 Answer

Replacing rear disk brake pads

Do I need any special tools to compress rear rotors, or other steps to protect the antilock brake system.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 61,037 Answers

No, a large metal "C" clamp works well, make sure the master cylinder doesn't overflow when you compress the cylinders back into the caliper.

Posted on Aug 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What tools do i need to remove rear brake pads on 95 cadillac deville?


You say pads, so I assume that you have rear disk brakes. The only special tool you will need is one to compress the rear calipers. Here is an image of the tool that is available at most all auto part stores.

Jul 30, 2014 | 1995 Cadillac DeVille

1 Answer

Steps to replacing rear brake pads


A special tool is required to compress the caliper piston on the rear brakes-don't use a C-clamp on the piston.
Raise the vehicle and remove the tire. The rear calipers have only one guide pin. Remove this pin and raise the caliper. Remove the old brake pads. Using the special tool compress the caliper piston-the piston will have one or two slots on it. These slots must in the correct position to remount the caliper. Install the new brake pads and slide the caliper back over the rotor and replace the guide pin. If the caliper doesn't slide over the rotor you'll need to reset the slots on the piston. Replace the tires and you're ready to go.

Jan 01, 2011 | 2000 Buick LeSabre

2 Answers

Change rear break pads on 2000 Buick. Cannot compress break cylinder in order to install new pads using C clamp and bleeding off break fluid.


There's a special tool required to compress the rear caliper pistons. You may want to rent the tool. If you look at the piston you'll see one or two notches. The special tool has nipples to fit these notches. The caliper piston will have to be compressed with the tool and the notches will have to be placed in the o'clock and 6 o'clock for the brake pads to slide over the rotor. If you rent the special tool have the renter show you how to use it.

Sep 11, 2010 | 2000 Buick LeSabre

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

3 Answers

Compressing the rear disc brake caliper on 2008 grand caravan


The rear calipers on these models require a special tool that compresses and turns the piston in at the same time -- most parts stores carry this tool.

It is called a caliper piston press -- and it installs where the pads would go and acts like a c-clamp,when turning handle it will turn the caliper piston backinto the caliper as it compresses it.
Anytime the brake rotor or brake pads are being replaced, the rear caliper piston must be seated (bottomed) to compensate for the new brake rotor or lining. Because the Parking Brake self-adjuster mechanism is attached to the piston, a special seating method is required. The only acceptable method is by rotating the piston back into the bore using Retractor,MILLER Special Tool 8807, . Any other seating method will damage the self-adjuster mechanism.
Good luck and hope this helps.

Mar 07, 2010 | Dodge Caravan Cars & Trucks

4 Answers

When trying to change the rear pads on a 2005 Montana SV6 I was not able to compress the caliper. It appears as if they need to have the pressure relieved from the system. Do I need to just apply more...


No, on rear wheel disc brakes, the pistons have to be turned in clockwise, and you need a special tool to do it, or you have something strong enough to put in the slots and turn it, but just turn them in far enough to get the new pads to slide over the rotors.

Nov 04, 2009 | 2005 Pontiac Montana SV6

1 Answer

Do i need to change the brake pads and discs???


No you don't, you can have them turn the brake disk/rotor . Turning the brake disk/rotor is when you have the surface of the disk resurfaced by having a brake lath cut the high spots down. The disk are cheap enough now that most will just replace the disk/rotor the same time they replace the brake pads. You can pick up performance drilled or slotted brake disk/rotor for almost the same price as the OEM disk/rotor. Good luck and hope this helps, you can pick up the slotted brake disk/rotor at Auto Zone for a reasonable price and they will have the step by step instruction replacing the disk and if you like to just have the disk/rotor turned, they can do they there too.

Jun 07, 2009 | 2002 Volvo S40

2 Answers

Rear Brakes 2005 Jetta


im sorry bro i find that you needing special tools a load of bs. i may be wrong but i really really doubt it. brakes are easy. first locate the caliper and there should be 2 bolts holding that tight. loosen the top bolt and then take out the lower bolt from the caliper. the old pads should just fall out. remove the master cylinder cap. (the jug with brake fluid in it.) compress the piston replace the old pads and push the claiper back down on the rotor. tighten bolts back up pump the brakes till hard with the car off and then repeat for the other side.

Apr 28, 2009 | 2003 Volkswagen Jetta TDI

4 Answers

Replace rear brake pads on a 2000 grand marquis


rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Mar 15, 2009 | 2000 Mercury Grand Marquis

1 Answer

Trying to release rear brake piston. 2007 Jetta 2.5


make sure you have the piston compressed all the way and the adjuster compressed all the way, if so check the thicknesses of the new pads and or rotors if they were replaced you may have a clearance problem that requires a little machining

Mar 15, 2009 | 2007 Volkswagen Jetta 2.5 Sedan

Not finding what you are looking for?
2004 Chevrolet Monte Carlo Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...