Question about Ford Transit Connect

1 Answer

Can you tell me how to install a master cylinder on my 1949 ford car. if you can i would appreciate it.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 157 Answers

What kind of ford car

Posted on Mar 16, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the master cylinder in a Ford Econovan


You must spray the brake lines with liquid wrench and let them soak for an hour then Just unbolt the lines amd move them out of the way unbolt the master cylinder and remove it you must bench bleed the new one to get the air out then install it and attach the lines then bleed the system starting with the wheel farthest from the master cylinder

Nov 25, 2016 | Ford Cars & Trucks

1 Answer

Install master cylinder on 1993 ford ranger


Check that the master cylinder push rod is disconnected from the brake petal under the dashboard.

Jun 01, 2014 | 1988 Ford Ranger

1 Answer

Clutch master and slave cylinder


Reservoir drained=got leak. Should be evident on one or other. Sometimes leaking at firewall hard to detect. Replace both, if one wore out the other won't be far behind. My 88 toyota pickup leaked there but replacement master cylinder rod was too long so had to use homemade spacer on firewall in engine compartment. Slave cylinder was a pain to get mounted.

Sep 29, 2017 | Cars & Trucks

1 Answer

Ford Explorer Master Cylinder replacement


you need to bleed the brakes as well

Jul 10, 2013 | 1996 Ford Explorer

1 Answer

1995 ford powerstroke replaced rear brake pads,hardware, drums, and master cylinder after much bleeding it stops but at standstill with brake pedal pressed the pedal begins to drop


OK, did you bench bleed the master cylinder before installing? If not, the warranty will be void, and the pedal will drop even if the rest of the hydraulic system is sealed.
I would try another new master cylinder if the bench bleeding was not performed and the master cylinder was deemed to be damaged.

If the master cylinder was bench bled, and it does this, maybe you can get it replaced with a new one under warranty.

Good luck on this repair.

Nov 06, 2011 | 1995 Ford F350

1 Answer

My 1986 ford bronco 2 with a 2.9l v6 needed a brake master cylinder. i replaced it with a brand new one, and noticed that the base of the master cylinder, where it mounts to the brake booster, is leaking a...


You should not have any fluid leaking.
1.The new master cylinder may have been manufacturer incorrectly, but unlikely. 2.Did you reuse the fluid tank or did it come with a new one? If you re-installed old tank, seal may have not seated correctly. 3. Did you tighten the brake lines correctly? 4. It may be that there was fluid that leaking into the booster from the old cylinder, and that fluid is now coming out of the booster with use. One indication would be if the reservoir tank is showing any fluid drop. If it is the problem is 1,2, or 3 above. Let me know what you find out by leaving a comment.
I hope this helps. Feel free to comment or ask further questions.

Thanks for using FixYa - a 4 THUMBS rating and POSITIVE TESTIMONIAL is appreciated for answering your FREE question.

Feb 09, 2011 | 1989 Ford Bronco II

2 Answers

Brakes squishy no leak


Mushy / squishy brakes are usually caused by the brake master cylinder seals failing. You can buy a rebuild kit or a re-built replacement master cylinder. I would recommend the rebuilt master cylinder as all the detail work has already been accomplished and it is not a huge expense. The key is to make sure that your use a bleeder kit to "Pre-bleed" the master kit before installation. Your making sure that the master cylinder is free of air before installation. If you instal it with air in the system it wil take you the better part of a quart of brake fluid to bleed the whole brake system via the wheel cylinders. What will happen is after you install the master cylinder the brakes would still be mushy and until you got the residual air out of all of the lines it would appear and act just like it did before you changed the master cylinder.

Thanks for using FixYa,

Kelly

Jun 03, 2010 | 2000 Ford Taurus

1 Answer

How to replace the oem clutch master cylinder on a 1988 ford f-150 ,,, where is it located on the truck?,,,


Removal:
1.From inside the cab, carefully pry the clutch master cylinder pushrod and retainer bushing from the pedal cross-shaft lever pin.
2. Disconnect and remove the interlock switch.
3. Remove as much fluid from reservoir as possible and place shop rags under the master cylinder to catch leaking fluid.
4. Disconnect hydraulic line from the master cylinder and plug lines and outlets to avoid contamination and excessive fluid loss.
5. Remove the two nuts retaining the clutch master cylinder.
6. Installation is the reverse of removal exept after installation, bled the system.

Feb 21, 2010 | 1988 Ford F 150

1 Answer

Spongy brakes


Does sound like you need a new master cylinder. On a 2000 you wont need to back bleed. You will just need to follow the instruction and bleed the master and all four points. you will probably need to bleed the ABS block and proportioning valve but only if they have bleeders on them.

May 31, 2009 | 2000 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...