Question about Daewoo Nubira

1 Answer

How do you remove the oil pan? Something is holding it up.

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,399 Answers

What kind of engine does it have? What make and model please?

Posted on Mar 16, 2011

  • Anonymous Mar 16, 2011

    It is a Daewoo Nubria. 2.0 DOHC

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Murphybanton
  • 2004 Answers

SOURCE: how to remove transmission oil pan on 2006 camry

Get a wrench or plyer

Posted on Apr 10, 2009

  • 58 Answers

SOURCE: removing oil pan on 2003 jeep wrangler with auto trans

use a pair of plyers and pull down on the plastic it should just be slid on the bolt take the tranny lines off the piece plastic first

Posted on Apr 11, 2009

Molson02536
  • 3854 Answers

SOURCE: pontiac montana oil pan bolt diagram for removal

If all the bolts are off, then the gasket is holding the oil pan in place and your going to have to tap it with a mallet, Not a hammer but a mallet so you don not damage the oil pan. Good luck and hope this helps.

Posted on Jul 13, 2009

  • 1 Answer

SOURCE: removing the oil pan from a 1994 vw jetta

you have to remove the oil pan without the gasket because the gasket is attached to your oil pan baffle and that can't be removed until you unbolt your oil pump. i pried the **** out of mine until i realized the gasket couldn't come with it. no haynes manual will explain it as simple as it could be, i hate those books

Posted on Aug 03, 2009

  • 14036 Answers

SOURCE: hi. how do i remove oil pan of audi a6 2007 2.0

YOU HAVE TO SUPPORT ENGINE WITH A ENGINE SUPPORT BRIDGETOOL 10-222A AND ENGINE SLING TOOL 2024A FROM THE TOP.BECAUSE YOU HAVE TO LOOSEN SUBFRAME MOUNTING BOLTS.SUPPORT THE SUBFRAME.REMOVE OR DISCONNECT THE FOLLOWING FRONT BOLTS NUMBER 2 AND 3.BOLT NUMBER 1 BOLT FROM THE SUBFRAME.SLOWLY LOWER THE FRAME.FOR MANUAL TRANSMISSION LOOSEN THE LEFT TRANSAXLE MOUNT NUT UNTIL IT IS ALIGNED WITH THE LOWER EDGE OF THE BOLT APPROX 4 TURNS.IF EQUIPPED WITH AUTOMATIC TRANSMISSION LOOSEN THE REAR BOLT FOR THE LEFT TRANSAXLE MOUNT SEVERAL TURNS THEN REMOVE THE FRONT BOLT FOR THE TRANSAXLE MOUNT.AT THE RIGHT TRANSAXLE MOUNT LOOSEN THE REAR BOLT MOUNT SEVERAL TURNS AND REMOVE THE FRONT BOLT.IF EQUIPPED WITH A MANUAL TRANSAXLE BOTH REAR BOLTS ON THE OIL PAN CAN BE ACESSED THROUGH THE OPENING ON THE FLYWHEEL TURN FLYWHEEL AS NEEDED.THEN REMOVE OIL PAN.

Posted on Apr 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change my oil pan gasket on my 95 ford Thunderbird, thank you first time car owner


Lift your car and place on jack stands. Then drain engine oil from pan. If there is/are any other steering or suspension components under oil pan, remove these first. Then, begin removing all bolts that hold pan in place. There should be a few bolts that come from the rear of the transmission section that also hold engine oil pan. Remove these. Once all bolts are removed, use a rubber mallet to tap oil pan until is breaks loose. If hard to remove, use a pry bar or flat head screw driver to pry oil pan off. Install in reverse order.

Dec 30, 2016 | Ford Cars & Trucks

1 Answer

How do i change the oil pump on a 2000 lexus es300


Drain oil from the oil pan and recycle. Remove bolts holding oil pan up and remove oil pan. Remove bolt holding oil pump in. Install new pump. Replace oil pan gasket if necessary. Reinstall oil pan. Reinstall drain plug and refill with oil. Start engine and watch oil pressure gauge or light. Oil pressure should be normal almost instantly. Check for oil leaks.

Jul 31, 2016 | 2000 Lexus ES 300

1 Answer

How do you change a gasket on the oil pan I have a 99 Chevy Cavalier


Drain the oil and remove the screws/bolts that hold the pan into place.

Then use a flat-blade screwdriver to gently prise the pan free.

Clean both mating surfaces of pan and block - remove all traces of the old gasket.

Smear some sealant compound on the oil pan - this will hold the new gasket in place. Put the new gasket onto the oil pan and align the bolt holes. Lift the pan into place and tighten the bolts.

The photo below is a generic image of oil pan with gasket.




26061843-wygqn0rnpnipldbddgjc2eqg-5-0.jpeg


26061843-wygqn0rnpnipldbddgjc2eqg-5-1.jpg

Jan 20, 2016 | Cars & Trucks

2 Answers

How do I change the oil pan gasket?


Whether it's an engine oil pan (called the 'sump'' in the UK) or a transmission oil pan the principle is the same on all vehicles.
1. Drain the oil

2. Remove the bolts holding the sump/pan in place:
change-oil-pan-gasket-mcgwfbeeztshkxy1nyom2hsg-4-0.jpg
change-oil-pan-gasket-mcgwfbeeztshkxy1nyom2hsg-4-1.jpg The oil drain plug, though depending on your vehicle it may look different:
change-oil-pan-gasket-mcgwfbeeztshkxy1nyom2hsg-4-3.jpg change-oil-pan-gasket-mcgwfbeeztshkxy1nyom2hsg-4-6.jpgNew gasket held in place with sealant
Use a blunt screwdriver -if needed - and prise the oil pan free. remove all traces of the old gasket from the mating surfaces.

Use a smear of sealant to hold the new gasket in the correct position on the pan - this will hold it in place when you refit the pan.

Push the pan into position and put in a front bolt finger-tight. Then put in a rear bolt finger-tight.

Putting in the bolts finger-tight allows you to gently 'move' the pan if needed to put the bolts in one at a time.

When all bolts are in, tighten them with a wrench/socket. Then check them all again for tightness.

It isn't actually a big job .. more 'messy' because of the oil.

Nov 04, 2015 | Cars & Trucks

1 Answer

How do I remove the oil pan on a 1999 chevy van 4.3


if the pan has never been off then manufacturers use an adhesive sealant to stick the pan on.
Be sure that ever bolt has been removed ( bolts at the main bearing caps at either end)
take a sharp object (old wood chisel) and a hammer and gently break the seal between the pan and the crankcase. work along the edge gently so as not to deform the edge of the pan.

Feb 12, 2015 | Cars & Trucks

1 Answer

How do you replace or fix ticking lifters


I,m going to share something with you that i found out my van had ticking lifters and all i did was clean the oil pan filter

1. drain all the oil from oil pan
2. take oil pan off
3. once that is done you will see a long tube comming down by the crank.
4. remove the 1 or 2 bolts that hold the filter on
5. once removed you can give it a good rinse out with a gas/2stroke oil mix
6. once fully dry replace back to original location
7 put new oil pan gasket on
8 put oil pan back on
9 torque bolts down to 12.5 foot pounds
10 full with oil
11 start vehicle and let run

Good luck!
Let me know how it turns out

Sep 10, 2011 | 2002 Dodge Durango

1 Answer

Oil pump ,,,where is the oil pump located on a 1997 dodge caravan


Hello
Welcome!
Oil pump is located on the oil pan.
Parts needed,,,oil,,,, oil filter,,,, oil pan gasket,,, oil pump,,,, oil pump pickup tube..
time to do this,, about 3 hours
Instructions,
Raise van place on 2 jack stands
drain oil remove oil filter fill new filter install.
remove bolts from oil pan,
remove oil pan..
remove 2 bolts that hold oil pump and tube.

install new pump and tube tork bolts to 45 fp
replace oil pan gasket and install oil pan
tork pan bolts to 35" pounds
install drain plug
fill with oil
start and check for leaks

let me know if i can help more

Jul 17, 2010 | 1997 Dodge Caravan

1 Answer

Replace oil pan on 2002 wrangler 4.0


Hi you will have to remove the exhaust and then remove the oil pan then you can use a spanner to hold the nut and remove the oil plug

Nov 08, 2009 | 2003 Jeep Wrangler

1 Answer

Pontiac montana oil pan bolt diagram for removal


If all the bolts are off, then the gasket is holding the oil pan in place and your going to have to tap it with a mallet, Not a hammer but a mallet so you don not damage the oil pan. Good luck and hope this helps.

Jul 13, 2009 | 2001 Pontiac Montana

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...