Question about Ford F-250

1 Answer

While driving, I had no fuel pedal responce, pulled over engine died. Was told MAF bad replaced still no start. Had diag.done said ecm bad replaced still no start. Engine spins, tries to start and exhaust smells like gas engine does when it needs tuneup.

Posted by on

  • Jeremy W.
    Jeremy W. Mar 16, 2011

    year, make, model, engine size?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 504 Answers

Check for SPARK AT PLUGS/CODE ECM TO SUIT KEY

Posted on Mar 16, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Mercury Mountaineer 5.0L dumping gas into intake manifold and detonation in exhaust manifold on exhaust firing cycle


Fuel pressure regulator bad. Vacuum operated , pull the vacuum line. Smells like fuel. It's bad .Electronic could a fuel pressure sensor on the fuel rail or the fuel pump control module.

Jul 28, 2015 | Mercury Cars & Trucks

1 Answer

Pontiac Aztek 2001 - 3.4l (non-GT); Codes: P0135, P0141, P0420 all O2 + Converter. Ideas on problem?


P0135 bank 1 sensor 1 open or short in wires,bad connections,bad sensor ,or bad ecm. P0141 bank 1 sensor 2 same diag as P0135. P0420 cat below threshold open or short, or faulty Ho2s sensors.you may have several problems. start with sensors circuit if good change sensors if not trace to ecm if reading not right replace ecm if all good replace sensors clear codes retest drive two drive cycles for cat to clear tests. then with no dtcs present test fuel pressure , injectors,then ignition system ,timing valves ,map,maf sensors,throttle sensor,crank sensor cam sensor, compression.

Aug 02, 2012 | 2001 Pontiac Aztek

1 Answer

I own a 2004 Isuzu Rodeo 3.2L V6 2WD. On saturday it died on me. at first i thought it might be the fuel pump because the engine turned over but wouldn't engage. Gas level was good as was the battery. ...


my problem was electrical, removing the batt (neg. terminal) for a few seconds resets the Engine Control Module (ECM) which operates the full pump relay, there should be a fuse in the relay box in under the hood labeled ECM or ECU. Pulling that fuse for 10 secs. or so also resets the ECM, try this and if it immediately works I suggest to drive it locally until it will not start again and repeat the removal of the ECM fuse. If this work out I suggest that you ECM is receiving a sensor signal to shut down the pump relay so I've been told, is the check engine lite on

Dec 07, 2010 | 2004 Isuzu Rodeo

1 Answer

1991 vette. Driving down the road and the engine just quit. Changed the fuel filter. Now if it starts, it idles low and if you try to press on the gas pedal, the engine dies. Engine won't rev up.


Have the TPS (Throttle Position Switch) checked with a milli-volt meter, it seems like it is not working properly or is dead. if it is not working it won't send a signal to the ECM (Computer) to let it know how much the accelerator pedal is being depressed so it cannot know how much give fuel and air to give the engine. Also have the MAF (Mass Air Flow) sensor checked.

Jun 15, 2010 | 1991 Chevrolet Corvette

1 Answer

1999 DURANGO IDLES BAD, CHECK ENGINE LIGHT ON, DIAG SAYS OPEN CIR


check to see if the cat is clogged if it is this will cause this to happen.

May 20, 2010 | 1999 Dodge Durango

2 Answers

Car will start but when pressing gas pedal, engine bogs down, can lightly tap pedal and get rpms up but no power when trying to drive. 3.2l v-6 1994 rodeo 4wd


I have seen alot of problems with the MAF (mass airflow meter) on these engines . Also make sure you do not have any cracks in the hose between the MAF and the engine and that all the hoses are connected. It will not run right with any air leaks between the MAF and engine. If there is not any cracks or hoses disconnected then you probably need a MAF. Try cleaning it first with some MAF cleaner spray. You can purchase it at any parts store.

Nov 17, 2009 | 1994 Isuzu Rodeo

2 Answers

2000 camero step on gas pedal car wants to die


your fuel filter might be old and clogged. try replacing it. if it is and not enough fuel can get through, the engine will stall when you let more air in (step on the gas pedal).

Oct 09, 2009 | 2000 Chevrolet Camaro

2 Answers

Engine starts then dies


Probably MAF. Mass air flow sensor, or idle control system/ sensor.
I have actually heard of some people having this problem because of a faulty heat sending unit, which doesn't show up on scan, but i'm still betting on the MAF. Good luck, let me know what you find.

Jun 22, 2009 | 1998 GMC Sierra

4 Answers

1985 Corvette, starts runs rough then dies


if you changed your fuel and that did not fixit its definitely the maf sensor.

Nov 26, 2008 | 1985 Chevrolet Corvette

1 Answer

Sluggish throttle responce


Clean the inside of the MAF sensor with MAF spray, it is made by CRC corp, a MAF will in most cases not set an engine code which turns on the check engine light.

Nov 11, 2008 | 1999 Kia Sportage

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...