Question about 1996 Toyota Camry

1 Answer

Install exterior door handle

Can someone please let me know how to do this step by step? Thanks

Posted by on

1 Answer

They are a pain in the ****! If you are a novice Iwouldnt reccomend doing it yourself. I did it but it requires taking the lock mechanism out, losening the window track and squeezzing your hands into the door. You will need a short 10mm open end wrench and a LOT of patience if its anything like the 1999 exterior door handle

Posted on Sep 03, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the driver's side door handle on a 1998 VW Jetta


There is only one screw holding the door handle in, the screw is right on the inside of the door. Its right above where the door attaches to the door.

Jan 08, 2013 | 1998 Volkswagen Jetta

1 Answer

My 2002 nissan altima exterior door handle's latch rod came completely out of where it came from while i was attempting to change the exterior door handle. i can't figure out how that latch rod...


Think there may be a bushing missing and that's also how you make adjustments as well. Below are some pictures I had from my service manual. It wasn't much but I hope it helps.


clifford224_647.gif

clifford224_648.gif

May 31, 2011 | 2002 Nissan Altima

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.



Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Dec 31, 2010 | 2002 Jaguar X-Type

1 Answer

2 x new exterior door handles + installation - 98 hyundai excel


I would suggest a junk yard, they might install it for you, if not, ask them who would.

Apr 16, 2010 | Hyundai Excel Cars & Trucks

1 Answer

Replace left front door outside handle pot metal tip broke off


SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual REMOVAL AND INSTALLATION Exterior Front Door Handle Removal and Installation
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
  1. Position the watershield aside.
  1. NOTE: The tie strap does not need to be reinstalled.
    If equipped, remove the tie strap from the anti-theft guard.
  1. Remove the screws and position the anti-theft guard aside.
  1. Release the clip and disconnect the exterior door handle actuating rod.
88661dd.gif
  1. Remove the anti-theft guard.
  1. Remove the exterior door handle screw.
  1. Remove the exterior handle actuating rod.
  1. Remove the exterior door handle lock cylinder cover.
  1. Remove the exterior door handle.

Apr 25, 2009 | 2001 Ford Escape

1 Answer

How to install exterior door handle on 95 Safari Van


hi, remove the entire door interior panel, keep notes and diagrams as you go, even take pics, usually the exterior handle is secured by 2 small screws or nuts, undo these and the handle will detach . there will be a small rod connected to this handle by a small clip or similar. reassembly is a reversal of the entire process, just take your time

Feb 11, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

How to replace '96 Ford Explorer driver side exterior door handle


You will need to remove the door panel to gain access to the handle. Roll the window up or down as needed to get to the nuts that attach the handle to the door. You will also need to remove a rod the goes to the door lock. You will see the rod after the door panel is removed. Good luck.

Jan 19, 2009 | 1996 Ford Explorer

1 Answer

Diagram for replacing exterior door handles


ok. first u remove the door panel(s), with the window rolled up, u will be able to see the back side of the exterior door handle. there will be three bolts, they are size 10metric. there is also a rod attached to the handle held in place by a plastic clip, remove the rod, then remove the three bolts. from the outside remove the exterior door handle being careful not to scratch painted surface. Repeat for the other door(s). Repeat this for installation.

Dec 14, 2008 | 1997 Toyota Camry

1 Answer

2001 Nissan Quest - Broken Exterior Sliding Door Handle


you can do this. you have to remove inside trim panel for access. if you still need to do, I will send you repair steps. let me know

Oct 16, 2008 | 2001 Nissan Quest

1 Answer

Replace exterior driver door handle


If you remove the inner door panel of the door there will be plastic weather shield covering most of the door. Use a hair dryer or heat gun to heat the weather shield up and slowly peel it away. There will be 2 (10mm I believe) bolts on the inside of the door panel to release the handle (have someone catch it from the other side). To re-install simply connect he handle rod and 2 bolts then place the door panel back on and your done. A word of advice is be gentle with the door panel so not to damage the door pins or crack the plastic. Taking your time can be fun when learning a car ;).

Jul 03, 2008 | 2000 Toyota Corolla

Not finding what you are looking for?
1996 Toyota Camry Logo

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...