Question about 1997 Chevrolet Camaro

1 Answer

Right turn signal dont blink. replaced flasher still eont blink.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,911 Answers

If the flasher is bad, then both sides will not work. you have a bad bulb in the system, you must track it down. note there is more than just one bulb in front and one in back, the side markers blink also so you must check them all. take a bulb out and put 12 volts to it from the battery.

Posted on Mar 16, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn lights blink with hazards but not with turn signal..flasher replaced. is It the multifunction lever then??


There should be a turn signal flasher and a hazard flasher. They are two different parts. If you replaced the hazard flasher and not the turn signal flasher than I would start by replacing the turn signal flasher.

One thing you can do once you find the turn signal flasher is to unplug it and use a jumper wire between the two pins of the connector then turn the key to the run position and place the turn signal lever in the left or right position. If the turn signal lights know light up than the turn signal flasher is the problem

Sep 09, 2014 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Turn signal flasher does not work


do you have bulbs blown? if not ,,go to fuse box under the dash look at fuse box to left or right. just at beside the fuses you will see a round flasher. pull it out, it will have 2 prongs on it. replace that with a new flasher and your turn signals will blink again.,,,,,,,,,,just to be sure you need a new one. answer this question,do turn signal lights come on but don't flash or blink? if thet don't,,replace the flasher.hope this help you!!

Aug 25, 2010 | 1998 Oldsmobile Aurora

2 Answers

Turn signals(blinkers) turn on but they dont blink?


Flasher module is burnt , just replace it.. you will find it in the fuse panel.

Jul 30, 2010 | 1991 Chevrolet S-10 Blazer

3 Answers

Turn signals dont blink.


You need to replace the turn signal flasher, it's a cylinder shape and may be silver or gold in color. When it goes bad, the turn signals stop flashing. Good luck and keep me posted.

Feb 16, 2010 | 1994 Chevrolet S-10 Blazer

3 Answers

97 olds 88, left turn signal not blinking.


possibly one side of your signal flasher is out turn on emergency flashers to locate one flasher then you can locate the other

Sep 12, 2009 | 1997 Oldsmobile 88

1 Answer

93 S10 left turn signals not working


Have you tried replacing the flasher? You'd think neither side would blink if the flasher was bad but I've seen this happen and it turned out to be the flasher. You could swap the signal flasher with the 4 way flasher to verify that's the problem before going out and buying one. Should be a few bucks at the parts store.

Apr 04, 2009 | 1996 Chevrolet S-10 Pickup

3 Answers

Turning signals dont blink


Problem is the Turn Signal "FLASHER" unit, 1.Turn on Emergency FLASHERS 2. Go under Dash while they are on Listen -for Clicking sound then feel for it 3. Should Be a Silver Round Unit About as Big IN ROUND as Half dollar coin 4. ok now Look Around for the SAME EXACT Thing Clipped onto Something Under dash At Driver side Usually Between Steering wheel and Center HUMP in Floor, 5. once you find it Take OUT the first One you Found Emergency FLASHER) and 6. Put it In Place of Turn Signal Flasher, 7. Turn off Emergency Flashers- Turn Key in "ON" Position but don't start then Try Turn Signals. Yaaaa !!!! they work ?? LoL hopefully this Does the trick, if they work Buy new one and Replace Always Use NEW For TURN Signals as they are used Much More than Emergency Flashers. Hope this is Good Instructions For you and Helps you Solve The Problem, Please DONT Forget to RATE ME Thank you Rejakwilson@aol.com

Jan 18, 2009 | 1986 Oldsmobile Cutlass Supreme

2 Answers

1997 sonoma turn signal flasher


it is inside, under dash, on left side is a plastic sound protector, mine had 3 screws holding it up, drop this down and straight in you will see a 1" round thing - this is the flasher, pull it out and replace with new one (there are two flat prongs that plug in). It appears this is a well guarded secret!

Aug 26, 2008 | 1997 GMC Sonoma

Not finding what you are looking for?
1997 Chevrolet Camaro Logo

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...