Question about 2006 Chevrolet Silverado

3 Answers

2006 chevy silverado 1500 4x4,i cant adjust the power steering?with the bolt and lock nut with exagone screw?excuse my english,iam speak french.thank,luc

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 492 Answers

There is no adjustment on the the box except to set the clearance between the gear and sector shaft. If the steering feels looses it may be caused by tie rods, pitman arm and other front end parts. Look for something loose or worn underneath while a friend turns the steering wheel back and forth.

Posted on Mar 16, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 836 Answers

If there is a looseness problem in the steering box, adjusting the preload setting WILL NOT cure the problem and may cause the gear to fail completely. The most common cause of loose steering on these trucks is a worn pitman arm as it's difficult to grease [ the arm is pressed onto the splined shaft of the steering box ]. Some of the others are tie-rod ends [ inner & outer ], idler arm, ball joints, whell hub bearings. I would check these first [ or have a Tech. ] before thinking the steering box is worn or faulty.

Posted on Mar 16, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 166 Answers

Why are you messing with it in the first place?? This is a job for someone who knows what they are doimg,,like a wheel alignment garage.

Posted on Mar 16, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 chevy S10 zr2 4x4


In the center of the gear box there is an adjustment screw to tighten or loosen the steering. It is usually and Allen key bolt/screw with a locking nut on it. Loosen the nut and adjust the center screw/bolt. I believe adjusting the screw clockwise is to tighten but I am not positive.

Apr 15, 2017 | Cars & Trucks

1 Answer

I have a 1998 chevy 2500.the sterling is hard to steer and the fluid is come out the cap.any idle what's going on.


Fluid Coming Out Power Steering Pump Cap - Taurus Car Club of ...

www.taurusclub.com > ... > Maintenance and Repair
Jan 9, 2010 - 2003 Vulcan has leak through cap on power steering pump. ... Hi I'm having the same thing happening to my 98 duratech. I was just getting ready to replace the rack today because of fluid coming out the drivers side boot... so decided to ... to be removed and that the bolt is recessed and difficult to reach.

Power steering issue - DodgeTalk : Dodge Car Forums, Dodge Truck ...

www.dodgetalk.com > ... > 2G Dodge RAM - General Talk
Jan 25, 2009 - Power steering issue 2G Dodge RAM - General Talk. ... Location:Sterling Heights, MI ..... pump, top off the reservior, screw on the cap, drop the truck and go drive it. .... I was able to loosen the pump and just dumped out the old fluid and.... I figured the belt was still good but the noise was definitely coming ...

Chevy Silverado Chrome Accessories - AutoAnything

www.autoanything.com/.../Chevy/.../110A50167A0A0A115A2690A1.as...
The Heartbeat has far better tastes when it comes to Chevy Silverado chrome accessories, and ... Check out our tail light chrome for Silverado rigs and you'll see what we mean. ... Chevy Silverado 2500HD Chrome Accessories .... 2012, 2011, 2010, 2009, 2008, 2007, 2006, 2005, 2004, 2003, 2002, 2001, 2000, 1999, 1998 ...

chevy bed rail caps - AutoAnything


Feb 03, 2016 | Sterling Cars & Trucks

1 Answer

I need to get the ball of the stick shift of my 2006 chevy


Gear lever balls ( if original ) are normally screwed on with a right hand thread . They are locked in place by a lock nut at the bottom under the ball and when that nut is screwed on further the ball becomes loose and can be taken off.. If the ball is over a flat bar then look for a hex headed grub screw near the bottom of the ball

Mar 18, 2014 | 2006 Chevrolet Silverado 2500HD

1 Answer

2001 Mitzubishi Montero Sport Steering Box


The steering box has an adjustment screw or bolt which is kept from turning by a lock nut. Loosen the lock nut and turn the screw or bolt
so as to reduce the play in your steering. The adjusting bolt is generally
located on top of the steering box.

Jan 04, 2013 | Cars & Trucks

1 Answer

How to remove belts from 1994 dodge caravan 2.5 liter


Drive Belts

Print


INSPECTION

See Figures 1, 2, 3, 4 and 5
Check the condition and tension of all drive belts every 12,000 miles, or at least once a year. Loose drive belts can lead to poor engine cooling and diminished alternator, power steering pump, air conditioning compressor, or emission air pump output. A belt that is too tight places a strain on the bearings in the driven component.


0900c15280215ae4.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: There are typically 3 types of accessory drive belts found on vehicles today


0900c15280215ae5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: An example of a healthy drive belt


0900c15280215ae6.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Deep cracks in this belt will cause flex, building up heat that will eventually lead to belt failure


0900c15280215ae7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: The cover of this belt is worn, exposing the critical reinforcing cords to excessive wear


0900c15280215ae8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Installing too wide a belt can result in serious belt wear and/or breakage
Replace any drive belt that is glazed, worn, cracked, or stretched to the point where correct adjustment tension is impossible. If two belts are used to drive a component, always replace both belts when replacement is necessary. After installing a new belt, run the engine for ten minutes, shut OFF the engine and recheck the belt tension. Readjust if necessary.


ADJUSTMENT

See Figures 6, 7, 8, 9 and 10


0900c15280215ae9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Engine belt tension chart-2.2L engines


0900c15280215aea.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Engine belt tension chart-1987-89 2.5L engines


0900c15280215aeb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 8: Engine belt tension chart-2.6L engines


0900c15280215aec.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 9: Engine belt tension chart-1990-93 models


0900c15280215aed.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 10: Engine belt tension chart-1994-95 models
Two popular methods of checking drive belt adjustment are; the Belt Tension Gauge Method and the Belt Deflection Method. The former requires a special gauge and the latter requires a straight edge and scale or just a good eye for measurement. The deflection method will be used in the following belt replacement instructions. A rule of thumb for checking belt tension by the deflection method is to determine the midpoint between two pulleys of the drive belt and press down at that point with moderate thumb pressure. The belt should deflect to the measurement indicated in the following installation procedures. Adjustment is necessary if the belt is either too loose or too tight.

WARNING A belt adjustment which is either too loose or too tight will eventually damage the accessory that belt is driving. A too loose adjustment allows free-play in the belt which could transfer a whipping motion or shock to the accessory drive pulley. Similarly, a belt which is too tight will preload the accessory bearings, leading to early failure.


REMOVAL & INSTALLATION

See Figure 11
Raise the front of the vehicle, support on jackstands and remove the lower splash shield if access is hampered due to space limitations when changing drive belts.


0900c15280215aee.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 11: Support the vehicle, then remove the lower right side splash shield for access to the drive belts
2.2L Engines
A/C COMPRESSOR DRIVE BELT
See Figures 12, 13 and 14


0900c15280215aef.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 12: A/C compressor drive belt adjusting points-2.2L engines


0900c15280215af0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 13: Loosening the locking screws for A/C compressor drive belt removal


0900c15280215af1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 14: Removing the A/C compressor drive belt from under the vehicle

  1. Loosen the idler pulley bracket pivot screw and the locking screw.
  2. Remove the belt and install a replacement.
  3. Using a breaker bar and socket apply torque to the welded nut provided on the mounted bracket to obtain proper tension.
  4. Tighten the locking screw first, followed by pivot screw. Tighten to 40 ft. lbs. (55 Nm).

ALTERNATOR DRIVE BELT (CHRYSLER TYPE)
See Figures 15 and 16


0900c15280215af2.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 15: Alternator belt adjustment-2.2L engine


0900c15280215af3.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 16: Loosening the locking screw for alternator drive belt removal
If removal of the alternator belt is required, the A/C belt must first be removed.

  1. Loosen the pivot nut, locking screw, and the adjusting screw.
  2. Remove the belt and install a replacement.
  3. Adjust to specification by tightening the adjusting screw.
  4. Tighten the locking screw to 25 ft. lbs. (34 Nm).
  5. Tighten the pivot nut to 30 ft. lbs. (41 Nm).

ALTERNATOR DRIVE BELT (BOSCH TYPE)
If removal of the alternator belt is required, the A/C belt must first be removed.
  1. Loosen the pivot nut, locking nut, and adjusting screw.
  2. Remove the belt and install a replacement.
  3. Adjust to specification by tightening the adjusting screw.
  4. Tighten the locking nut to 25 ft. lbs. (34 Nm).
  5. Tighten the pivot nut to 30 ft. lbs. (41 Nm).

POWER STEERING BELT
If removal of the power steering belt is required, the A/C and alternator belts must first be removed.
  1. Loosen the locking screw, and pivot screw.
  2. Remove the belt and install a replacement.
  3. Install a 1 / 2 in. breaker bar into the pump bracket slot, apply pressure with the breaker bar and adjust the belt to specification.
  4. Tighten the locking screw first, then the pivot screw. Tighten to 40 ft. lbs. (55 Nm).

AIR PUMP DRIVE BELT
See Figure 17


0900c15280215af5.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 17: Air pump belt adjustment-2.2L engines
When servicing the air pump, use the square holes provided in the pulley to prevent camshaft rotation.

  1. Remove the nuts and bolts retaining the drive pulley cover.
  2. Remove the locking bolt and pivot bolt from the pump bracket, then remove the pump.
  3. Remove the belt and install a replacement.
  4. Position the pump, then install the locking bolt and pivot bolt finger-tight.
  5. Install a 1 / 2 in. breaker bar into the bracket assembly (block the drive pulley to prevent camshaft rotation), and adjust the belt to specification.
  6. Tighten locking bolt and pivot bolt to 25 ft. lbs. (35 Nm).

2.5L Engines
AIR CONDITIONING COMPRESSOR
See Figure 18


0900c15280215af8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 18: Drive belt adjustment points-2.5L engines

  1. Loosen the idler bracket pivot screw and the locking screws to replace, or adjust belt.
  2. Remove the belt and install a replacement.
  3. Adjust the belt to specification by applying torque to weld nut on the idler bracket.
  4. Tighten locking screw first, followed by the pivot screw. Tighten to 40 ft. lbs. (55 Nm).

ALTERNATOR BELT
See Figure 18
If replacement of the alternator belt is required, the A/C drive belt must first be removed.
  1. Loosen the pivot nut, locking nut, and adjusting screw.
  2. Remove the belt and install a replacement.
  3. Adjust the belt to specification by tightening the adjusting screw.
  4. Tighten the locking nut to 25 ft. lbs. (35 Nm).
  5. Tighten the pivot nut to 30 ft. lbs. (40 Nm).

POWER STEERING PUMP
See Figure 18
If replacement of the power steering belt is required, the A/C and alternator belts must first be remove.
  1. Loosen the locking screw and pivot screw to replace, or adjust the belt.
  2. Remove the belt and install a replacement.
  3. Using a 1 / 2 in. breaker bar positioned in adjusting bracket slot, adjust the belt to specification.
  4. Tighten the locking screw followed by the pivot screw. Tighten to 40 ft. lbs. (55 Nm).

2.6L Engines
ALTERNATOR/AIR CONDITIONING COMPRESSOR BELT
See Figure 19


0900c15280215af9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 19: Drive belt adjustment points-2.6L engines

  1. Loosen the locking screw, jam nut, and pivot nut.
  2. Loosen the adjusting screw.
  3. Remove the belt and install a replacement.
  4. Adjust the belt to specification by tightening the adjusting screw.
  5. Tighten the locking screw followed by the pivot nut. Tighten to 16 ft. lbs. (22 Nm).
  6. Tighten the jam nut to 21 ft. lbs. (28 Nm).

POWER STEERING PUMP BELT
See Figure 19
If replacement of the power steering belt is required, the alternator and A/C belt must first be remove.
  1. Loosen the pivot screw, and the locking screw.
  2. Remove the timing pickup.
  3. Remove the belt and install a replacement.
  4. Install a 1 / 2 in. breaker bar in the adjusting bracket slot, torque to specification.
  5. Tighten the locking screw, followed by the pivot screw. Tighten to 40 ft. lbs. (55 Nm).
  6. Install the timing pick-up, and tighten to 160 inch lbs. (18 Nm).

Jul 26, 2012 | 1994 Dodge Grand Caravan

1 Answer

How do I replace the serpentine belt on a 1994 concorde?


Remove the alternator/power steering pump and water pump drive belt to gain access to the air conditioning drive belt.
To remove and install the air conditioning compressor drive belt, first loosen the tensioner pulley lock nut, then turn the adjusting screw to raise or lower the tensioner pulley assembly Accessory Drive - 3.3L Engine or Accessory Drive - 3.5L Engine To adjust the air conditioning drive belt, loosen the tensioner pulley nut and adjust belt tension by tightening adjusting screw. Torque pulley nut to 54 N•m (40 ft. lbs.) after adjustment.
The Poly-V generator/power steering belt has an adjustable tensioner pulley located on the timing belt cover Accessory Drive - 3.5L Engine to maintain proper belt tension. To remove or install this belt, Release tension by loosening the tensioner pulley nut and adjustment bolt Accessory Drive - 3.5L Engine Reverse procedure to install and tighten belt to specified tension.

Jul 10, 2012 | 1994 Chrysler Concorde

1 Answer

What is the rear axle nut torque specifications on 2006 Silverado 4x4


Fastener Tightening Specifications 140 foot pounds for the wheels all the way around. Application
Specification
Metric
English
Spare Tire Hoist Retaining Bolt
40 N·m
30 lb ft
Wheel Nuts
190 N·m
140 lb ft

Dec 14, 2010 | 2006 Chevrolet Silverado 2500HD 2WD

1 Answer

Does anyone know how to adjust the steering box for 1986 Chevy Suburban K10 4x4?


There should be a sector shaft screw with a lock nut on it, on top of the steering box. Loosen the lock nut and adjust by turning the sector shaft screw, some use a flat blade screwdriver, others use an allen wrench.

Oct 19, 2010 | 1986 Chevrolet Suburban

1 Answer

2001 chevy silverado steering wheel vibration problem


bent alloy, bent steel rim, broken belting inside of tire(caused from hitting a good size hole). lug nuts not torqued to correct ft lbs, outer or inner tie rods, toe/ cmber out of adjustment. Are the tires wearing? If not, forget the camber/toe

Dec 14, 2009 | 2006 Chevrolet Trailblazer

1 Answer

How do i remove the ignition swicth from a 2004 chevy siverado 1500


The procedure to remove the ignition switch is
  1. Start by disconnecting you negative battery cable.
  2. Wait at least 1 minute to disable your airbag system.
  3. Remove the airbag from the steering wheel, it's retained by a couple bolts on the back of the steering wheel.
  4. Disconnect the wires to it, and set it aside.
  5. Remove the clip that is above the lock nut for the steering wheel, then remove the lock nut.
  6. You need a steering wheel puller to pull the steering wheel off. After you remove the steering wheel, you should have access to the turn signal switch.

Sep 18, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

Not finding what you are looking for?
2006 Chevrolet Silverado Logo

464 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...