Question about 1965 Ford Mustang

2 Answers

We have a fully rebuilt 351 winsor, and we've can only get 20-25 pounds oil presure? we've tried another new oil pump, and it's the same.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.


    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Did they install new cam bearings if so a cam bearing turned wrong could cause problem what pump did you install the best pump is high volume not high pressure

Posted on Aug 04, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Master
  • 331 Answers

You should be getting 35-40 Psi @2000 rpm. It could be incorrect bearing clearances.
Very small changes in main bearing clearance make for large changes in oil pressure.

Posted on Aug 02, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 81 f250 351 winsor isnt getting spark ignition module ,coil ,distributor,cap and rotor,plugs and wires all new i gapped plugs at .044 help

got +12v to the ign coil? does the coil spark if you ground the negative(-) terminal? does the distributor rotor rotate? it may be time to replace the distributor sproket and module (stator and armature).

Apr 16, 2015 | Ford F-250 Cars & Trucks

1 Answer

Need vacum line arrangement for 351 winsor

the diagram should be under the hood or use a haynes manual

Dec 05, 2014 | Cars & Trucks

1 Answer

Will a ford 351 winsor fit in a bronco with a 302, without any wiring problems

Yes. I've done it. If you still have the donor vehicle there is an additional vacuum canister in the passenger's fender you'll need (or to plug off the lines) and a few other small additions. Otherwise it's just a straight forward R&R same harness. Please rate my assistance and thanks for using fixya.

Jun 29, 2011 | 1992 Ford Bronco

1 Answer

I have a 1985 ford econoline 351 winsor when I press the brake the signal lights will light up ,this does not interfear with the turn sighnals


Apr 09, 2011 | 1985 Ford Econoline

1 Answer

I have a 1984 F150 with s 351 winsdor engine.l. my carburator allows the gas to leak into my oil and my plugs are constantly getting wet.... truck wont start up rite.

sounds like there is alot of dirt in the carburetor and it should be pulled apart cleaned and rebuilt with a new kit that comes with the necessary parts.also install a new accelerator pump in the carb.change the oil and dry out the plugs if they are in good shape.

Mar 18, 2011 | 1984 Ford F 150

1 Answer

I have a ford f-250 with a 351 in it 10300mi. original engine having oil presure problems, startes up goes right up to 50 or 60 pounds but after it warms up it goes back down to 20 or 25 crusing and 8 to...

Could be your oil pump going bad, could also be because the bearing tolerances in your motor have gotten larger due to the mileage, especially if your oil hasn't been chnged regularly. Try a lower viscosity oil, it is easier for the oil pump to pumo thru the system.

Apr 09, 2010 | 1983 Ford F 250

2 Answers

In need for a manual for my 351 winsor

Go to faxonautoliterature. They carry manufacturer original service manuals. Most are reasonably priced and their service is excellent. Hope this helps.

Nov 14, 2009 | 1966 Ford Mustang

2 Answers

Need to know firing order for 1996 f150 with a 351 winsor

Firing order is 1-3-7-2-6-5-4-8 with Number 1 cylinder on the right front.

Oct 03, 2009 | 1993 Ford F150 SuperCab

3 Answers

83 ford f-250 351. starts but will not idle

If its a (holley) motorcraft 2 bbl carb sounds like the power valve. They typically blow out whenever the engine backfires or they just wear out after time and flood the idle circuit.

Aug 04, 2009 | 1983 Ford F 250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

71338 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides